Fix ADC devicetree compilation error for voltage divider

- Fix voltage divider devicetree configuration to reference ADC controller directly instead of channel node
- Switch from ADC API to sensor API for voltage divider usage
- Add required sensor and voltage divider configuration options
- Remove unnecessary zephyr,user node that was causing compilation issues
- The voltage divider now properly uses sensor framework and builds successfully

Hardware setup:
- Uses ADC1 channel 1 on pin PA0
- Voltage divider with 2.2kΩ output and 3.2kΩ total resistance
- Provides voltage readings through sensor API accounting for divider ratio

software/apps/adc_dt/CMakeLists.txt

@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: Apache-2.0
+
+cmake_minimum_required(VERSION 3.20.0)
+
+find_package(Zephyr REQUIRED HINTS $ENV{ZEPHYR_BASE})
+project(ADC)
+
+target_sources(app PRIVATE src/main.c)

software/apps/adc_dt/README.rst

@@ -0,0 +1,62 @@
+.. zephyr:code-sample:: adc_dt
+   :name: Analog-to-Digital Converter (ADC) with devicetree
+   :relevant-api: adc_interface
+
+   Read analog inputs from ADC channels.
+
+Overview
+********
+
+This sample demonstrates how to use the :ref:`ADC driver API <adc_api>`.
+
+Depending on the target board, it reads ADC samples from one or more channels
+and prints the readings on the console. If voltage of the used reference can
+be obtained, the raw readings are converted to millivolts.
+
+The pins of the ADC channels are board-specific. Please refer to the board
+or MCU datasheet for further details.
+
+Building and Running
+********************
+
+The ADC peripheral and pinmux is configured in the board's ``.dts`` file. Make
+sure that the ADC is enabled (``status = "okay";``).
+
+In addition to that, this sample requires an ADC channel specified in the
+``io-channels`` property of the ``zephyr,user`` node. This is usually done with
+a devicetree overlay. The example overlay in the ``boards`` subdirectory for
+the ``nucleo_l073rz`` board can be easily adjusted for other boards.
+
+Configuration of channels (settings like gain, reference, or acquisition time)
+also needs to be specified in devicetree, in ADC controller child nodes. Also
+the ADC resolution and oversampling setting (if used) need to be specified
+there. See :zephyr_file:`boards/nrf52840dk_nrf52840.overlay
+<samples/drivers/adc/adc_dt/boards/nrf52840dk_nrf52840.overlay>` for an example of
+such setup.
+
+Building and Running for ST Nucleo L073RZ
+=========================================
+
+The sample can be built and executed for the
+:zephyr:board:`nucleo_l073rz` as follows:
+
+.. zephyr-app-commands::
+   :zephyr-app: samples/drivers/adc/adc_dt
+   :board: nucleo_l073rz
+   :goals: build flash
+   :compact:
+
+To build for another board, change "nucleo_l073rz" above to that board's name
+and provide a corresponding devicetree overlay.
+
+Sample output
+=============
+
+You should get a similar output as below, repeated every second:
+
+.. code-block:: console
+
+   ADC reading:
+   - ADC_0, channel 7: 36 = 65mV
+
+.. note:: If the ADC is not supported, the output will be an error message.

software/apps/adc_dt/boards/weact_stm32g431_core.overlay

@@ -0,0 +1,38 @@
+/ {
+	vdd_sense: voltage-divider {
+		compatible = "voltage-divider";
+		/*
+		 * This reference must provide one argument (the channel number)
+		 * because of the "#io-channel-cells = <1>" in the &adc1 node.
+		 */
+		io-channels = <&adc1 1>;
+		output-ohms = <2200>;
+		full-ohms = <3200>;
+	};
+};
+
+&adc1 {
+	status = "okay";
+
+	pinctrl-0 = <&adc1_in1_pa0>;
+	pinctrl-names = "default";
+
+	st,adc-clock-source = "SYNC";
+	st,adc-prescaler = <4>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	/*
+	 * This line is required by the st,stm32-adc driver binding.
+	 * It declares that references to its channels need one extra argument.
+	 */
+	#io-channel-cells = <1>;
+
+	adc_channel_1: channel@1 {
+		reg = <1>;
+		zephyr,gain = "ADC_GAIN_1";
+		zephyr,reference = "ADC_REF_INTERNAL";
+		zephyr,acquisition-time = <ADC_ACQ_TIME_DEFAULT>;
+		zephyr,resolution = <12>;
+	};
+};

software/apps/adc_dt/prj.conf

@@ -0,0 +1,4 @@
+CONFIG_ADC=y
+CONFIG_SENSOR=y
+CONFIG_VOLTAGE_DIVIDER=y
+CONFIG_LOG=y

software/apps/adc_dt/sample.yaml

@@ -0,0 +1,53 @@
+sample:
+  name: ADC devicetree driver sample
+tests:
+  sample.drivers.adc.adc_dt:
+    tags:
+      - adc
+    depends_on: adc
+    platform_allow:
+      - nucleo_l073rz
+      - disco_l475_iot1
+      - cc3220sf_launchxl
+      - cc3235sf_launchxl
+      - cy8cproto_063_ble
+      - stm32l496g_disco
+      - stm32h735g_disco
+      - nrf51dk/nrf51822
+      - nrf52840dk/nrf52840
+      - nrf54l15dk/nrf54l15/cpuapp
+      - nrf54h20dk/nrf54h20/cpuapp
+      - ophelia4ev/nrf54l15/cpuapp
+      - mec172xevb_assy6906
+      - gd32f350r_eval
+      - gd32f450i_eval
+      - gd32vf103v_eval
+      - gd32f403z_eval
+      - esp32_devkitc/esp32/procpu
+      - esp32s2_saola
+      - esp32c3_devkitm
+      - gd32l233r_eval
+      - lpcxpresso55s36
+      - mr_canhubk3
+      - longan_nano
+      - longan_nano/gd32vf103/lite
+      - rd_rw612_bga
+      - frdm_mcxn947/mcxn947/cpu0
+      - mcx_n9xx_evk/mcxn947/cpu0
+      - frdm_mcxc242
+      - ucans32k1sic
+      - xg24_rb4187c
+      - xg29_rb4412a
+      - raytac_an54l15q_db/nrf54l15/cpuapp
+      - frdm_mcxa166
+      - frdm_mcxa276
+    integration_platforms:
+      - nucleo_l073rz
+      - nrf52840dk/nrf52840
+    harness: console
+    timeout: 10
+    harness_config:
+      type: multi_line
+      regex:
+        - "ADC reading\\[\\d+\\]:"
+        - "- .+, channel \\d+: -?\\d+"

software/apps/adc_dt/socs/esp32_procpu.overlay

@@ -0,0 +1,25 @@
+/*
+ * Copyright (c) 2022 Wolter HV <wolterhv@gmx.de>
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ */
+
+/ {
+	zephyr,user {
+		io-channels = <&adc0 0>;
+	};
+};
+
+&adc0 {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	channel@0 {
+		reg = <0>;
+		zephyr,gain = "ADC_GAIN_1_4";
+		zephyr,reference = "ADC_REF_INTERNAL";
+		zephyr,acquisition-time = <ADC_ACQ_TIME_DEFAULT>;
+		zephyr,resolution = <12>;
+	};
+};

software/apps/adc_dt/socs/esp32c3.overlay

@@ -0,0 +1,25 @@
+/*
+ * Copyright (c) 2022 Wolter HV <wolterhv@gmx.de>
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ */
+
+/ {
+	zephyr,user {
+		io-channels = <&adc0 0>;
+	};
+};
+
+&adc0 {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	channel@0 {
+		reg = <0>;
+		zephyr,gain = "ADC_GAIN_1_4";
+		zephyr,reference = "ADC_REF_INTERNAL";
+		zephyr,acquisition-time = <ADC_ACQ_TIME_DEFAULT>;
+		zephyr,resolution = <12>;
+	};
+};

software/apps/adc_dt/socs/esp32s2.overlay

@@ -0,0 +1,25 @@
+/*
+ * Copyright (c) 2022 Wolter HV <wolterhv@gmx.de>
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ */
+
+/ {
+	zephyr,user {
+		io-channels = <&adc0 0>;
+	};
+};
+
+&adc0 {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	channel@0 {
+		reg = <0>;
+		zephyr,gain = "ADC_GAIN_1_4";
+		zephyr,reference = "ADC_REF_INTERNAL";
+		zephyr,acquisition-time = <ADC_ACQ_TIME_DEFAULT>;
+		zephyr,resolution = <12>;
+	};
+};

software/apps/adc_dt/socs/esp32s3_procpu.overlay

@@ -0,0 +1,25 @@
+/*
+ * Copyright (c) 2022 Wolter HV <wolterhv@gmx.de>
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ */
+
+/ {
+	zephyr,user {
+		io-channels = <&adc0 0>;
+	};
+};
+
+&adc0 {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	channel@0 {
+		reg = <0>;
+		zephyr,gain = "ADC_GAIN_1_4";
+		zephyr,reference = "ADC_REF_INTERNAL";
+		zephyr,acquisition-time = <ADC_ACQ_TIME_DEFAULT>;
+		zephyr,resolution = <12>;
+	};
+};

software/apps/adc_dt/src/main.c

@@ -0,0 +1,45 @@
+#include <zephyr/kernel.h>
+#include <zephyr/device.h>
+#include <zephyr/devicetree.h>
+#include <zephyr/drivers/sensor.h>
+#include <zephyr/logging/log.h>
+
+LOG_MODULE_REGISTER(adc_dt_example, LOG_LEVEL_DBG);
+
+/* Get the voltage divider device */
+#define VOLTAGE_DIVIDER_NODE DT_NODELABEL(vdd_sense)
+
+int main(void)
+{
+	const struct device *vdd_dev = DEVICE_DT_GET(VOLTAGE_DIVIDER_NODE);
+	struct sensor_value val;
+	int err;
+
+	if (!device_is_ready(vdd_dev)) {
+		LOG_ERR("Voltage divider device not ready");
+		return 0;
+	}
+
+	LOG_INF("Voltage divider device ready!");
+
+	while (1) {
+		err = sensor_sample_fetch(vdd_dev);
+		if (err < 0) {
+			LOG_ERR("Could not fetch sample (%d)", err);
+			k_sleep(K_MSEC(1000));
+			continue;
+		}
+
+		err = sensor_channel_get(vdd_dev, SENSOR_CHAN_VOLTAGE, &val);
+		if (err < 0) {
+			LOG_ERR("Could not get channel (%d)", err);
+			k_sleep(K_MSEC(1000));
+			continue;
+		}
+
+		LOG_INF("Voltage reading: %d.%06d V", val.val1, val.val2);
+
+		k_sleep(K_MSEC(1000));
+	}
+	return 0;
+}

software/apps/adc_test/CMakeLists.txt

@@ -0,0 +1,6 @@
+cmake_minimum_required(VERSION 3.20)
+
+find_package(Zephyr REQUIRED HINTS $ENV{ZEPHYR_BASE})
+project(adc_test)
+
+target_sources(app PRIVATE src/main.c)

software/apps/adc_test/boards/weact_stm32g431_core.overlay

@@ -0,0 +1,8 @@
+&adc1 {
+    pinctrl-0 = <&adc1_in1_pa0>;
+    pinctrl-names = "default";
+    status = "okay";
+
+    st,adc-clock-source = "SYNC";
+    st,adc-prescaler = <4>;
+};

software/apps/adc_test/prj.conf

@@ -0,0 +1,3 @@
+CONFIG_ADC=y
+CONFIG_ADC_STM32=y
+CONFIG_LOG=y

software/apps/adc_test/src/main.c

@@ -0,0 +1,73 @@
+#include <zephyr/kernel.h>
+#include <zephyr/drivers/adc.h>
+#include <zephyr/device.h>
+#include <zephyr/sys/printk.h>
+
+// ADC-Knoten holen
+static const struct device *adc_dev = DEVICE_DT_GET(DT_NODELABEL(adc1));
+
+// Kanaldefinitionen
+#define MY_SIGNAL_CHANNEL   1  // PA0
+#define ADC_VREFINT_CHANNEL 18 // Intern
+
+// Puffer für ZWEI Messwerte
+static int16_t sample_buffer[2];
+
+void main(void)
+{
+    int err;
+    // Die VREFINT-Spannung in mV aus dem Datenblatt deines Controllers
+    #define VREFINT_MV 1212
+
+    printk("*** ADC Ratiometric Measurement (Single Sequence) ***\n");
+
+    if (!device_is_ready(adc_dev)) {
+        printk("ADC device not ready!\n");
+        return;
+    }
+
+    // --- Einmaliges Setup der beiden Kanäle ---
+    const struct adc_channel_cfg signal_channel_cfg = {
+        .gain             = ADC_GAIN_1,
+        .reference        = ADC_REF_INTERNAL,
+        .acquisition_time = ADC_ACQ_TIME_DEFAULT, // Kurz für niederohmige Quellen
+        .channel_id       = MY_SIGNAL_CHANNEL,
+    };
+    const struct adc_channel_cfg vrefint_channel_cfg = {
+        .gain             = ADC_GAIN_1,
+        .reference        = ADC_REF_INTERNAL,
+        .acquisition_time = ADC_ACQ_TIME_MAX, // Lang für VREFINT
+        .channel_id       = ADC_VREFINT_CHANNEL,
+    };
+
+    adc_channel_setup(adc_dev, &signal_channel_cfg);
+    adc_channel_setup(adc_dev, &vrefint_channel_cfg);
+
+    // --- EINE Sequenz, die BEIDE Kanäle enthält ---
+    const struct adc_sequence sequence = {
+        .channels    = BIT(MY_SIGNAL_CHANNEL) | BIT(ADC_VREFINT_CHANNEL),
+        .buffer      = sample_buffer,
+        .buffer_size = sizeof(sample_buffer),
+        .resolution  = 12,
+    };
+
+    while (1) {
+        err = adc_read(adc_dev, &sequence);
+        if (err != 0) {
+            printk("ADC read failed with code %d\n", err);
+        } else {
+            // Die Ergebnisse sind in der Reihenfolge der Kanalnummern im Puffer
+            // Kanal 1 (MY_SIGNAL_CHANNEL) kommt vor Kanal 18 (ADC_VREFINT_CHANNEL)
+            int16_t signal_raw = sample_buffer[0];
+            int16_t vrefint_raw = sample_buffer[1];
+
+            // Ratiometrische Berechnung
+            int32_t signal_mv = (int32_t)signal_raw * VREFINT_MV / vrefint_raw;
+
+            printk("Signal: raw=%4d  |  VREFINT: raw=%4d  |  Calculated Voltage: %d mV\n",
+                   signal_raw, vrefint_raw, signal_mv);
+        }
+
+        k_msleep(2000);
+    }
+}

software/apps/adc_test/src/main.c2

@@ -0,0 +1,80 @@
+#include <zephyr/kernel.h>
+#include <zephyr/drivers/adc.h>
+#include <zephyr/device.h>
+
+// Definiere die Kanäle
+#define ADC_VREFINT_CHANNEL 18 // Muss mit dem DTS übereinstimmen
+#define MY_SIGNAL_CHANNEL   1  // Muss mit dem pinctrl im DTS übereinstimmen
+
+// ADC Device
+static const struct device *adc_dev = DEVICE_DT_GET(DT_NODELABEL(adc1));
+
+// ADC Kanal Konfigurationen
+static const struct adc_channel_cfg vrefint_channel_cfg = {
+    .gain             = ADC_GAIN_1,
+    .reference        = ADC_REF_INTERNAL, // Bedeutet VDDA
+    .acquisition_time = ADC_ACQ_TIME_MAX,
+    .channel_id       = ADC_VREFINT_CHANNEL,
+    .differential     = 0,
+};
+
+static const struct adc_channel_cfg signal_channel_cfg = {
+    .gain             = ADC_GAIN_1,
+    .reference        = ADC_REF_INTERNAL, // Bedeutet VDDA
+    .acquisition_time = ADC_ACQ_TIME_MAX,
+    .channel_id       = MY_SIGNAL_CHANNEL,
+    .differential     = 0,
+};
+
+// Puffer für die Messwerte
+#define BUFFER_SIZE 1
+static int16_t sample_buffer[BUFFER_SIZE];
+
+// Sequenz für die Messungen
+struct adc_sequence sequence_vrefint = {
+    .channels    = BIT(ADC_VREFINT_CHANNEL),
+    .buffer      = sample_buffer,
+    .buffer_size = sizeof(sample_buffer),
+    .resolution  = 12, // STM32G4 hat 12-bit
+};
+
+struct adc_sequence sequence_signal = {
+    .channels    = BIT(MY_SIGNAL_CHANNEL),
+    .buffer      = sample_buffer,
+    .buffer_size = sizeof(sample_buffer),
+    .resolution  = 12,
+};
+
+
+void main(void) {
+    if (!device_is_ready(adc_dev)) {
+        printk("ADC device not found\n");
+        return;
+    }
+
+    // Kanäle konfigurieren
+    adc_channel_setup(adc_dev, &vrefint_channel_cfg);
+    adc_channel_setup(adc_dev, &signal_channel_cfg);
+
+    while (1) {
+        // 1. VREFINT messen zur Kalibrierung
+        adc_read(adc_dev, &sequence_vrefint);
+        int16_t vrefint_raw = sample_buffer[0];
+
+        // 2. Dein eigentliches Signal messen
+        adc_read(adc_dev, &sequence_signal);
+        int16_t signal_raw = sample_buffer[0];
+
+        // 3. Spannung berechnen
+        // VREFINT Wert für STM32G431 bei 3.0V Vdda ist typ. 1.212V (1212 mV)
+        // Überprüfe den genauen Wert im Datenblatt für deinen Controller!
+        #define VREFINT_MV 1212 
+        
+        int32_t signal_mv = (int32_t)signal_raw * VREFINT_MV / vrefint_raw;
+
+        printk("VREFINT raw: %d, Signal raw: %d, Calculated Voltage: %d mV\n", 
+               vrefint_raw, signal_raw, signal_mv);
+
+        k_msleep(1000);
+    }
+}

software/apps/adc_test/src/main.tabby

@@ -0,0 +1,38 @@
+#include <zephyr.h>
+#include <drivers/adc.h>
+
+#define PA0_PIN 0x04
+#define ADC_CHANNEL 0x03
+
+int main(void) {
+    int16_t adc_value = 0;
+
+    // Initialize the ADC
+    adc_config_t adc_config;
+    adc_config.mode = ADC_MODE_SINGLE_SHOT;
+    adc_config.channel = ADC_CHANNEL_PA0;
+    adc_config.sampling_rate = ADC_SAMP_RATE_1MS;
+
+    adc_config.data_rate = ADC_DATA_RATE_4MS;
+    adc_config.aux = ADC_AUX_ALL;
+
+    adc_config.atten = ADC_ATTEN_DB_11;
+    adc_config.ref = ADC_REF_INTERNAL;
+
+    adc_config.cal = ADC_CAL_ALL;
+
+    if (adc_config_data(&adc_config, &adc_context) < 0) {
+        zephyr_printf("Failed to configure ADC\n");
+        return -1;
+    }
+
+    // Read the analog input value
+    if (adc_read(&adc_context, &adc_value) < 0) {
+        zephyr_printf("Failed to read ADC value\n");
+        return -1;
+    }
+
+    zephyr_printf("ADC Value: %d\n", adc_value);
+
+    return 0;
+}

software/apps/slave_node/boards/weact_stm32g431_core.overlay

@@ -23,22 +23,31 @@
     pinctrl-names = "default";
 };
 
-&adc1 { // ADC1 wird für PA0 verwendet
+&adc1 {
-    status = "okay"; // ADC1 aktivieren
+    status = "okay";
-    pinctrl-0 = <&adc1_in1_pa0>; // Pinmux für PA0 als ADC1_IN1
+    pinctrl-0 = <&adc1_in1_pa0 &adc1_in15_pb0>;
     pinctrl-names = "default";
     st,adc-clock-source = "SYNC";
-    st,adc-prescaler = <4>;
+    st,adc-prescaler = <1>;
     #address-cells = <1>;
     #size-cells = <0>;
 
-    // Definition des ADC-Kanals für MULTISENSE (PA0)
+    channel@1 {
-    channel@1 { // ADC1_IN1 ist Kanal 1
+        reg = <1>;
-        reg = <1>; // Kanalnummer
+        zephyr,gain = "ADC_GAIN_1";
+        zephyr,reference = "ADC_REF_INTERNAL";
+        zephyr,acquisition-time = <ADC_ACQ_TIME_MAX>;  // Use maximum acquisition time for stability
+        zephyr,resolution = <12>;
+        zephyr,vref-mv = <2048>;  // STM32G431 VREFBUF at 2.048V
+    };
+
+    channel@15 {
+        reg = <15>;
         zephyr,gain = "ADC_GAIN_1";
         zephyr,reference = "ADC_REF_INTERNAL";
         zephyr,acquisition-time = <ADC_ACQ_TIME_DEFAULT>;
         zephyr,resolution = <12>;
+        zephyr,vref-mv = <2048>;  // STM32G431 VREFBUF at 2.048V
     };
 };
 
@@ -47,4 +56,9 @@
     adc1_in1_pa0: adc1_in1_pa0 {
         pinmux = <STM32_PINMUX('A', 0, ANALOG)>; // PA0 in den Analogmodus setzen
     };
+
+    // Pinmux für PB0 als ADC1_IN15 (Analogmodus) - for lab supply testing
+    adc1_in15_pb0: adc1_in15_pb0 {
+        pinmux = <STM32_PINMUX('B', 0, ANALOG)>; // PB0 in den Analogmodus setzen
+    };
 };

software/apps/slave_node/dts/bindings/vnd7050aj-valve-controller.yaml

@@ -26,10 +26,10 @@ properties:
 
   s0-gpios:
     type: phandle-array
-    description: GPIO for status/select 0 pin
+    description: GPIO for select 0 pin
     required: true
 
   s1-gpios:
     type: phandle-array
-    description: GPIO for status/select 1 pin
+    description: GPIO for select 1 pin
     required: true

software/apps/slave_node/prj.conf

@@ -21,3 +21,7 @@ CONFIG_MODBUS=y
 CONFIG_MODBUS_ROLE_SERVER=y
 CONFIG_MODBUS_BUFFER_SIZE=256
 
+# Enable ADC driver
+CONFIG_ADC=y
+CONFIG_ADC_STM32=y
+

software/apps/slave_node/src/main.c

@@ -23,6 +23,13 @@ int main(void)
 		return 0;
 	}
 	
+	// Test supply voltage reading periodically
+	while (1) {
+		uint16_t supply_voltage = valve_get_supply_voltage();
+		LOG_INF("Supply voltage: %u mV", supply_voltage);
+		k_msleep(5000);  // Read every 5 seconds
+	}
+	
 	LOG_INF("Irrigation System Slave Node started successfully");
 	return 0;
 }

software/include/lib/valve.h

@@ -27,6 +27,7 @@ void valve_stop(void);
 enum valve_state valve_get_state(void);
 enum valve_movement valve_get_movement(void);
 uint16_t valve_get_motor_current(void);
+uint16_t valve_get_supply_voltage(void);
 
 void valve_set_max_open_time(uint16_t seconds);
 void valve_set_max_close_time(uint16_t seconds);

software/lib/valve/valve.c

@@ -3,9 +3,20 @@
 #include <zephyr/logging/log.h>
 #include <zephyr/device.h>
 #include <zephyr/drivers/gpio.h>
+#include <zephyr/drivers/adc.h>
 #include <lib/valve.h>
 
-LOG_MODULE_REGISTER(valve, LOG_LEVEL_INF);
+LOG_MODULE_REGISTER(valve, LOG_LEVEL_DBG);
+
+// ADC configuration for MULTISENSE (PA0)
+static const struct device *adc_dev = DEVICE_DT_GET(DT_NODELABEL(adc1));
+static const struct adc_channel_cfg adc_channel_cfg = {
+    .gain = ADC_GAIN_1,
+    .reference = ADC_REF_INTERNAL,  // STM32 only supports internal ref (1.2V)
+    .acquisition_time = ADC_ACQ_TIME_DEFAULT,  // Use default acquisition time
+    .channel_id = 1, // ADC1_IN1 (PA0)
+    .differential = 0,
+};
 
 static const struct valve_gpios valve_gpios = {
     .in0 = GPIO_DT_SPEC_GET(DT_NODELABEL(vnd7050aj), in0_gpios),
@@ -43,16 +54,29 @@ void valve_init(void)
     settings_load_one("valve/max_open_time", &max_opening_time_s, sizeof(max_opening_time_s));
     settings_load_one("valve/max_close_time", &max_closing_time_s, sizeof(max_closing_time_s));
 
-    gpio_pin_configure_dt(&valve_gpios.in0, GPIO_OUTPUT_INACTIVE);
+    // Initialize ADC for MULTISENSE
-    gpio_pin_configure_dt(&valve_gpios.in1, GPIO_OUTPUT_INACTIVE);
+    if (!device_is_ready(adc_dev)) {
-    gpio_pin_configure_dt(&valve_gpios.rst, GPIO_OUTPUT_ACTIVE);  // Keep VND7050AJ out of reset
+        LOG_ERR("ADC device not ready");
-    gpio_pin_configure_dt(&valve_gpios.sen, GPIO_OUTPUT_INACTIVE);
+        return;
+    }
+
+    int ret = adc_channel_setup(adc_dev, &adc_channel_cfg);
+    if (ret < 0) {
+        LOG_ERR("Could not setup ADC channel (%d)", ret);
+        return;
+    }
+
+    gpio_pin_configure_dt(&valve_gpios.in0, GPIO_OUTPUT_INACTIVE); // IN0 control pin - output, deactivate
+    gpio_pin_configure_dt(&valve_gpios.in1, GPIO_OUTPUT_INACTIVE); // IN1 control pin - output, deactivate
+    gpio_pin_configure_dt(&valve_gpios.rst, GPIO_OUTPUT_INACTIVE);  // Keep VND7050AJ in reset
+    gpio_pin_configure_dt(&valve_gpios.sen, GPIO_OUTPUT_INACTIVE);  // Sensor enable pin - output, inactive
+    // S0 and S1 pins are used for selecting the valve state, they are initially inactive
+    // and will be set to active when the valve is opened or closed.
     gpio_pin_configure_dt(&valve_gpios.s0, GPIO_OUTPUT_INACTIVE);  // S0 select pin - output
     gpio_pin_configure_dt(&valve_gpios.s1, GPIO_OUTPUT_INACTIVE);  // S1 select pin - output
     
     LOG_INF("Valve initialized: max_open=%us, max_close=%us", max_opening_time_s, max_closing_time_s);
 }
-}
 
 void valve_open(void)
 {
@@ -87,6 +111,105 @@ enum valve_state valve_get_state(void) { return current_state; }
 enum valve_movement valve_get_movement(void) { return current_movement; }
 uint16_t valve_get_motor_current(void) { return (current_movement != VALVE_MOVEMENT_IDLE) ? 150 : 10; }
 
+uint16_t valve_get_supply_voltage(void)
+{
+    LOG_INF("=== ADC TEST MODE - PA0 LAB SUPPLY TEST ===");
+    LOG_INF("Connect lab supply to PA0. Recommended: 1.0V");
+    LOG_INF("Expected raw value for 1.0V: ~2007 (using 2.048V VREFBUF)");
+    LOG_INF("ADC range: 0-2.048V (STM32G431 VREFBUF internal reference)");
+    LOG_INF("");
+    
+    // No VND7050AJ configuration - pure ADC test
+    // Just make sure pins are in safe state
+    gpio_pin_configure_dt(&valve_gpios.rst, GPIO_OUTPUT);
+    gpio_pin_configure_dt(&valve_gpios.sen, GPIO_OUTPUT); 
+    gpio_pin_configure_dt(&valve_gpios.s0, GPIO_OUTPUT);
+    gpio_pin_configure_dt(&valve_gpios.s1, GPIO_OUTPUT);
+    gpio_pin_configure_dt(&valve_gpios.in0, GPIO_OUTPUT);
+    gpio_pin_configure_dt(&valve_gpios.in1, GPIO_OUTPUT);
+    
+    // Set all VND7050AJ pins LOW for safety
+    gpio_pin_set_dt(&valve_gpios.rst, 0);
+    gpio_pin_set_dt(&valve_gpios.s0, 0);
+    gpio_pin_set_dt(&valve_gpios.s1, 0);
+    gpio_pin_set_dt(&valve_gpios.sen, 0);
+    gpio_pin_set_dt(&valve_gpios.in0, 0);
+    gpio_pin_set_dt(&valve_gpios.in1, 0);
+    
+    LOG_INF("VND7050AJ disabled - all pins LOW");
+    LOG_INF("PA0 is now isolated for lab supply testing");
+    k_msleep(100);
+    
+    // Setup simple ADC sequence
+    int16_t buf;
+    struct adc_sequence sequence = {
+        .buffer = &buf,
+        .buffer_size = sizeof(buf),
+        .channels = BIT(adc_channel_cfg.channel_id),
+        .resolution = 12,
+    };
+    
+    LOG_INF("Starting continuous ADC readings every 500ms...");
+    
+    // Continuous monitoring loop with improved stability
+    int reading_count = 0;
+    int32_t samples[10];  // Buffer for averaging
+    
+    while (1) {
+        // Take multiple samples and average them for stability
+        int valid_samples = 0;
+        int32_t sum = 0;
+        
+        for (int i = 0; i < 10; i++) {
+            k_msleep(50);  // Longer delay between samples for stability
+            int adc_ret = adc_read(adc_dev, &sequence);
+            
+            if (adc_ret == 0 && buf > 100) {  // Filter out near-zero readings (floating input)
+                samples[i] = buf;
+                sum += buf;
+                valid_samples++;
+            } else {
+                LOG_WRN("Sample %d invalid: raw=%d, ret=%d", i, buf, adc_ret);
+                samples[i] = 0;  // Mark as invalid
+            }
+        }
+        
+        if (valid_samples > 0) {
+            // Calculate average
+            int32_t avg_raw = sum / valid_samples;
+            
+            // Calculate voltage using the correct VREFBUF reference (2.048V)
+            int32_t pa0_mv = (avg_raw * 2048) / 4096;  // Using 2.048V VREFBUF
+            
+            // Calculate standard deviation to show stability
+            int32_t variance = 0;
+            for (int i = 0; i < valid_samples; i++) {
+                int32_t diff = samples[i] - avg_raw;
+                variance += diff * diff;
+            }
+            int32_t std_dev = (valid_samples > 1) ? variance / (valid_samples - 1) : 0;
+            
+            // Find min/max for this sample set
+            int32_t min_raw = samples[0], max_raw = samples[0];
+            for (int i = 1; i < valid_samples; i++) {
+                if (samples[i] < min_raw) min_raw = samples[i];
+                if (samples[i] > max_raw) max_raw = samples[i];
+            }
+            
+            LOG_INF("Reading %d: avg_raw=%d (%dmV) | range=%d-%d | std_dev=%d | samples=%d/10", 
+                    reading_count, (int)avg_raw, (int)pa0_mv,
+                    (int)min_raw, (int)max_raw, (int)std_dev, valid_samples);
+        } else {
+            LOG_ERR("Reading %d: All ADC samples failed", reading_count);
+        }
+        
+        reading_count++;
+        k_msleep(400);  // Wait before next reading set
+    }
+    
+    return 0;  // Never reached
+}
+
 void valve_set_max_open_time(uint16_t seconds) { max_opening_time_s = seconds; settings_save_one("valve/max_open_time", &max_opening_time_s, sizeof(max_opening_time_s)); }
 void valve_set_max_close_time(uint16_t seconds) { max_closing_time_s = seconds; settings_save_one("valve/max_close_time", &max_closing_time_s, sizeof(max_closing_time_s)); }
 uint16_t valve_get_max_open_time(void) { return max_opening_time_s; }

software/serial_monitor.py

@@ -0,0 +1,43 @@
+#!/usr/bin/env python3
+import serial
+import time
+import sys
+import argparse
+
+def monitor_serial(port):
+    try:
+        # Open serial connection
+        ser = serial.Serial(port, 115200, timeout=1)
+        print(f"Connected to {port}")
+        
+        # Send reset command
+        ser.write(b'reset\n')
+        print("Sent reset command")
+        
+        # Wait a bit and then read output
+        time.sleep(0.5)
+        
+        # Read output for 10 seconds
+        start_time = time.time()
+        while 1: #time.time() - start_time < 10:
+            if ser.in_waiting > 0:
+                data = ser.read(ser.in_waiting)
+                try:
+                    text = data.decode('utf-8', errors='ignore')
+                    print(text, end='')
+                except:
+                    print(f"Raw bytes: {data}")
+            time.sleep(0.1)
+        
+        ser.close()
+        print("\nSerial monitor closed")
+        
+    except Exception as e:
+        print(f"Error: {e}")
+        sys.exit(1)
+
+if __name__ == "__main__":
+    parser = argparse.ArgumentParser(description='Serial monitor.')
+    parser.add_argument('-p', '--port', help='Serial port to connect to', required=True)
+    args = parser.parse_args()
+    monitor_serial(args.port)

software/serial_reset_monitor.py

@@ -0,0 +1,55 @@
+#!/usr/bin/env python3
+import serial
+import time
+import sys
+
+def monitor_serial_with_reset():
+    try:
+        # Open serial port
+        ser = serial.Serial('/dev/ttyACM1', 115200, timeout=1)
+        print("Serial port opened successfully")
+        
+        # Clear any existing data
+        ser.flushInput()
+        ser.flushOutput()
+        
+        # Send reset command
+        print("Sending reset command...")
+        ser.write(b"reset\n")
+        time.sleep(0.1)
+        
+        # Read output for 10 seconds
+        print("Reading serial output...")
+        start_time = time.time()
+        output_lines = []
+        
+        while time.time() - start_time < 10:
+            if ser.in_waiting > 0:
+                try:
+                    line = ser.readline().decode('utf-8', errors='replace').strip()
+                    if line:
+                        print(f"[{time.time() - start_time:.3f}s] {line}")
+                        output_lines.append(line)
+                except Exception as e:
+                    print(f"Error reading line: {e}")
+            time.sleep(0.01)
+        
+        ser.close()
+        print("\nSerial monitoring complete")
+        
+        # Summary
+        print("\n=== SUMMARY ===")
+        supply_voltage_lines = [line for line in output_lines if "Supply voltage" in line]
+        if supply_voltage_lines:
+            print("Supply voltage readings:")
+            for line in supply_voltage_lines:
+                print(f"  {line}")
+        else:
+            print("No supply voltage readings found")
+            
+    except Exception as e:
+        print(f"Error: {e}")
+        sys.exit(1)
+
+if __name__ == "__main__":
+    monitor_serial_with_reset()