Sync

.vscode/launch.json

@@ -0,0 +1,19 @@
+{
+	"version": "0.2.0",
+	"configurations": [
+		{
+			"type": "nrf-connect",
+			"request": "launch",
+			"name": "Launch firmware/build_nrf52840dk_debug",
+			"config": "${workspaceFolder}/firmware/build_nrf52840dk_debug",
+			"runToEntryPoint": "main"
+		},
+		{
+			"type": "nrf-connect",
+			"request": "launch",
+			"name": "Launch firmware/build_buzzy/firmware",
+			"config": "${workspaceFolder}/firmware/build_buzzy/firmware",
+			"runToEntryPoint": "main"
+		}
+	]
+}

.vscode/settings.json

@@ -6,5 +6,9 @@
     "nrf-connect.boardRoots": [
         "${workspaceFolder}/firmware"
     ],
-    "cmake.sourceDirectory": "C:/Projekte/buzzer_2/firmware/libs/ble_mgmt"
+    "cmake.sourceDirectory": "C:/Projekte/buzzer_2/firmware/libs/ble_mgmt",
+    "nrf-connect.debugging.bindings": {
+        "${workspaceFolder}/firmware/build_nrf52840dk_debug": "Launch firmware/build_nrf52840dk_debug",
+        "${workspaceFolder}/firmware/build_buzzy/firmware": "Launch firmware/build_buzzy/firmware"
+    }
 }

.vscode/tasks.json

@@ -0,0 +1,26 @@
+{
+    "version": "2.0.0",
+    "tasks": [
+        {
+            "label": "MAC RTT Streamer",
+            "type": "shell",
+            "command": "bash",
+            "args": [
+                "-c",
+                "while true; do nc localhost 19021; sleep 0.2; done"
+            ],
+            "presentation": {
+                "echo": false,
+                "reveal": "always",
+                "focus": false,
+                "panel": "shared",
+                "showReuseMessage": false,
+                "clear": true
+            },
+            "runOptions": {
+                "runOn": "folderOpen"
+            },
+            "problemMatcher": []
+        }
+    ]
+}

firmware/VERSION

@@ -1,6 +1,6 @@
 VERSION_MAJOR = 0
 VERSION_MINOR = 0
-PATCHLEVEL = 6
+PATCHLEVEL = 77
 VERSION_TWEAK = 0
 #if (IS_ENABLED(CONFIG_LOG))
 EXTRAVERSION = debug

firmware/boards/buzzy_nrf52840.conf

@@ -1,11 +1,2 @@
-### Console / Logging: RTT
+# Keep QSPI NOR page layout aligned with generated LittleFS block size (4KB).
-CONFIG_USE_SEGGER_RTT=y
+CONFIG_NORDIC_QSPI_NOR_FLASH_LAYOUT_PAGE_SIZE=4096
-CONFIG_CONSOLE=y
-CONFIG_RTT_CONSOLE=y
-
-CONFIG_UART_CONSOLE=n
-CONFIG_LOG_BACKEND_UART=n
-CONFIG_LOG_BACKEND_RTT=y
-
-# Keep SPI NOR page layout aligned with generated LittleFS block size (4KB).
-CONFIG_SPI_NOR_FLASH_LAYOUT_PAGE_SIZE=4096

firmware/boards/iten/buzzy/board.yml

@@ -1,5 +1,6 @@
 board:
   name: buzzy
+  full_name: Buzzy
   vendor: iten
   socs:
     - name: nrf52840

firmware/boards/iten/buzzy/buzzy-pinctrl.dtsi

@@ -18,47 +18,47 @@
 		};
 	};
 	
-	spi3_default: spi3_default {
+	// spi3_default: spi3_default {
-		group1 {
+	// 	group1 {
-			psels = <NRF_PSEL(SPIM_SCK, 0, 2)>,
+	// 		psels = <NRF_PSEL(SPIM_SCK, 0, 2)>,
-			<NRF_PSEL(SPIM_MOSI, 0, 29)>,
+	// 		<NRF_PSEL(SPIM_MOSI, 0, 29)>,
-			<NRF_PSEL(SPIM_MISO, 0, 30)>;
+	// 		<NRF_PSEL(SPIM_MISO, 0, 30)>;
-		};
+	// 	};
-	};
+	// };
 	
-	spi3_sleep: spi3_sleep {
+	// spi3_sleep: spi3_sleep {
-		group1 {
+	// 	group1 {
-			psels = <NRF_PSEL(SPIM_SCK, 0, 2)>,
+	// 		psels = <NRF_PSEL(SPIM_SCK, 0, 2)>,
-			<NRF_PSEL(SPIM_MOSI, 0, 29)>,
+	// 		<NRF_PSEL(SPIM_MOSI, 0, 29)>,
-			<NRF_PSEL(SPIM_MISO, 0, 30)>;
+	// 		<NRF_PSEL(SPIM_MISO, 0, 30)>;
-			low-power-enable;
+	// 		low-power-enable;
-		};
+	// 	};
-	};
+	// };
 	
 	/*
 	* Optional future QSPI pinctrl states (keep disabled for now).
 	* Use these when switching from &spi3 to &qspi in buzzy.dts.
 	*/
-	// qspi_default: qspi_default {
+	qspi_default: qspi_default {
-	// 	group1 {
+		group1 {
-	// 		psels = <NRF_PSEL(QSPI_SCK, 0, 2)>,
+			psels = <NRF_PSEL(QSPI_SCK, 0, 2)>,
-	// 		<NRF_PSEL(QSPI_CSN, 0, 5)>,
+			<NRF_PSEL(QSPI_CSN, 0, 5)>,
-	// 		<NRF_PSEL(QSPI_IO0, 0, 29)>,
+			<NRF_PSEL(QSPI_IO0, 0, 29)>,
-	// 		<NRF_PSEL(QSPI_IO1, 0, 30)>,
+			<NRF_PSEL(QSPI_IO1, 0, 30)>,
-	// 		<NRF_PSEL(QSPI_IO2, 0, 31)>,
+			<NRF_PSEL(QSPI_IO2, 0, 31)>,
-	// 		<NRF_PSEL(QSPI_IO3, 1, 13)>;
+			<NRF_PSEL(QSPI_IO3, 1, 13)>;
-	// 	};
+		};
-	// };
+	};
-	
+	
-	// qspi_sleep: qspi_sleep {
+	qspi_sleep: qspi_sleep {
-	// 	group1 {
+		group1 {
-	// 		psels = <NRF_PSEL(QSPI_SCK, 0, 2)>,
+			psels = <NRF_PSEL(QSPI_SCK, 0, 2)>,
-	// 		<NRF_PSEL(QSPI_CSN, 0, 5)>,
+			<NRF_PSEL(QSPI_CSN, 0, 5)>,
-	// 		<NRF_PSEL(QSPI_IO0, 0, 29)>,
+			<NRF_PSEL(QSPI_IO0, 0, 29)>,
-	// 		<NRF_PSEL(QSPI_IO1, 0, 30)>,
+			<NRF_PSEL(QSPI_IO1, 0, 30)>,
-	// 		<NRF_PSEL(QSPI_IO2, 0, 31)>,
+			<NRF_PSEL(QSPI_IO2, 0, 31)>,
-	// 		<NRF_PSEL(QSPI_IO3, 1, 13)>;
+			<NRF_PSEL(QSPI_IO3, 1, 13)>;
-	// 		low-power-enable;
+			low-power-enable;
-	// 	};
+		};
-	// };
+	};
 };

firmware/boards/iten/buzzy/buzzy.dts

@@ -54,7 +54,7 @@
 	charger_status {
 		compatible = "gpio-keys";
 		chg_status: chg_status {
-			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpio0 13 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>;
 			label = "ETA6003_CHG_STATUS";
 		};
 	};
@@ -137,17 +137,52 @@
 *   SO/SIO1-> P0.30
 *   CS     -> P0.05
 */
-&spi3 {
+// &spi3 {
+// 	status = "okay";
+// 	pinctrl-0 = <&spi3_default>;
+// 	pinctrl-1 = <&spi3_sleep>;
+// 	pinctrl-names = "default", "sleep";
+// 	cs-gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+
+// 	mx25r64: flash@0 {
+// 		compatible = "jedec,spi-nor";
+// 		reg = <0>;
+// 		spi-max-frequency = <8000000>;
+// 		jedec-id = [c2 28 17];
+// 		size = <DT_SIZE_M(64)>;
+// 		has-dpd;
+// 		t-enter-dpd = <10000>;
+// 		t-exit-dpd = <35000>;
+
+// 		partitions {
+// 			compatible = "fixed-partitions";
+// 			#address-cells = <1>;
+// 			#size-cells = <1>;
+
+// 			ext_flash_lfs: partition@0 {
+// 				label = "ext-littlefs";
+// 				reg = <0x00000000 DT_SIZE_M(8)>;
+// 			};
+// 		};
+// 	};
+// };
+
+/*
+* Optional future QSPI variant (keep disabled for now):
+* - Disable &spi3 block above.
+* - Enable &qspi block below.
+* - Keep the same flash partition layout.
+*/
+&qspi {
 	status = "okay";
-	pinctrl-0 = <&spi3_default>;
+	pinctrl-0 = <&qspi_default>;
-	pinctrl-1 = <&spi3_sleep>;
+	pinctrl-1 = <&qspi_sleep>;
 	pinctrl-names = "default", "sleep";
-	cs-gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
 	
 	mx25r64: flash@0 {
-		compatible = "jedec,spi-nor";
+		compatible = "nordic,qspi-nor";
 		reg = <0>;
-		spi-max-frequency = <8000000>;
+		sck-frequency = <32000000>;
 		jedec-id = [c2 28 17];
 		size = <DT_SIZE_M(64)>;
 		has-dpd;
@@ -167,47 +202,6 @@
 	};
 };
 
-/*
-* Optional future QSPI variant (keep disabled for now):
-* - Disable &spi3 block above.
-* - Enable &qspi block below.
-* - Keep the same flash partition layout.
-*/
-// &qspi {
-// 	status = "okay";
-// 	pinctrl-0 = <&qspi_default>;
-// 	pinctrl-1 = <&qspi_sleep>;
-// 	pinctrl-names = "default", "sleep";
-
-// 	mx25r64: flash@0 {
-// 		compatible = "nordic,qspi-nor";
-// 		reg = <0>;
-// 		jedec-id = [c2 28 17];
-// 		size = <DT_SIZE_M(64)>;
-// 		has-dpd;
-// 		t-enter-dpd = <10000>;
-// 		t-exit-dpd = <35000>;
-
-// 		/* Net mapping from hardware: *
-// 		* SCK=P0.02, CSN=P0.05, IO0=P0.29, IO1=P0.30, IO2=P0.31, IO3=P1.13
-// 		*/
-// 		sck-pin = <2>;
-// 		csn-pins = <5>;
-// 		io-pins = <29>, <30>, <31>, <45>;
-
-// 		partitions {
-// 			compatible = "fixed-partitions";
-// 			#address-cells = <1>;
-// 			#size-cells = <1>;
-
-// 			ext_flash_lfs: partition@0 {
-// 				label = "ext-littlefs";
-// 				reg = <0x00000000 DT_SIZE_M(8)>;
-// 			};
-// 		};
-// 	};
-// };
-
 
 &gpio0 {
 	status = "okay";

firmware/boards/nrf52840dk_nrf52840.conf

@@ -1,4 +0,0 @@
-### Console / Logging: UART
-CONFIG_UART_CONSOLE=y
-CONFIG_LOG_BACKEND_UART=y
-CONFIG_LOG_BACKEND_RTT=n

firmware/boards/nrf52840dk_nrf52840.overlay

@@ -34,3 +34,16 @@
     pinctrl-1 = <&i2s0_sleep>;
     pinctrl-names = "default", "sleep";
 };
+
+&mx25r64 {
+    partitions {
+        compatible = "fixed-partitions";
+        #address-cells = <1>;
+        #size-cells = <1>;
+
+        ext_flash_lfs: partition@0 {
+            label = "ext-littlefs";
+            reg = <0x00000000 DT_SIZE_M(8)>;
+        };
+    };
+};

firmware/build_output.txt

@@ -0,0 +1,22 @@
+-- west build: making build dir /Users/edi/nrf_playground/buzzer_2/firmware/build pristine
+WARNING: This looks like a fresh build and BOARD is unknown; so it probably won't work. To fix, use --board=<your-board>.
+Note: to silence the above message, run 'west config build.board_warn false'
+-- west build: generating a build system
+Loading Zephyr module(s) (Zephyr base): sysbuild_default
+-- Found Python3: /opt/nordic/ncs/toolchains/322ac893fe/opt/python@3.12/bin/python3.12 (found suitable version "3.12.4", minimum required is "3.10") found components: Interpreter
+-- Cache files will be written to: /Users/edi/Library/Caches/zephyr
+-- Found west (found suitable version "1.4.0", minimum required is "0.14.0")
+CMake Error at /opt/nordic/ncs/v3.2.1/zephyr/cmake/modules/extensions.cmake:3518 (message):
+  BOARD is not being defined on the CMake command-line, in the environment or
+  by the app.
+Call Stack (most recent call first):
+  /opt/nordic/ncs/v3.2.1/zephyr/cmake/modules/boards.cmake:61 (zephyr_check_cache)
+  cmake/modules/sysbuild_default.cmake:15 (include)
+  /opt/nordic/ncs/v3.2.1/zephyr/share/zephyr-package/cmake/ZephyrConfig.cmake:75 (include)
+  /opt/nordic/ncs/v3.2.1/zephyr/share/zephyr-package/cmake/ZephyrConfig.cmake:92 (include_boilerplate)
+  /opt/nordic/ncs/v3.2.1/zephyr/share/sysbuild-package/cmake/SysbuildConfig.cmake:8 (include)
+  template/CMakeLists.txt:10 (find_package)
+
+
+-- Configuring incomplete, errors occurred!
+FATAL ERROR: command exited with status 1: /opt/homebrew/bin/cmake -DWEST_PYTHON=/opt/nordic/ncs/toolchains/322ac893fe/opt/python@3.12/bin/python3.12 -B/Users/edi/nrf_playground/buzzer_2/firmware/build -GNinja -S/opt/nordic/ncs/v3.2.1/zephyr/share/sysbuild -DAPP_DIR:PATH=/Users/edi/nrf_playground/buzzer_2/firmware

firmware/debug.conf

@@ -1,8 +1,29 @@
 ### Logging
 CONFIG_LOG=y
-CONFIG_AUDIO_LOG_LEVEL_DBG=y
+#CONFIG_LOG_MODE_IMMEDIATE=y
+CONFIG_DEBUG=y
 
 CONFIG_DEBUG_OPTIMIZATIONS=y
 
 CONFIG_INIT_STACKS=y
 CONFIG_THREAD_STACK_INFO=y
+
+### Lib logging levels
+# CONFIG_BATT_MGMT_LOG_LEVEL_DBG=y
+# CONFIG_BATT_MGMT_BLINK_INTERVAL_LOGGING=y
+# CONFIG_USB_MGMT_LOG_LEVEL_DBG=y
+CONFIG_BUZZ_PROTO_LOG_LEVEL_DBG=y
+
+### Bluetooth
+CONFIG_BLE_MGMT=y
+CONFIG_BT_LOG_LEVEL_WRN=y
+
+### Audio
+CONFIG_BUZZ_AUDIO=n
+
+### Shell features shared by all debug variants
+CONFIG_SHELL=y
+CONFIG_SHELL_LOG_BACKEND=y
+CONFIG_FILE_SYSTEM_SHELL=y
+CONFIG_SHELL_STACK_SIZE=2048
+CONFIG_FILE_SYSTEM_SHELL_LS_SIZE=y

firmware/debug_rtt.conf

@@ -0,0 +1,15 @@
+### Debug transport: RTT
+CONFIG_CONSOLE=y
+CONFIG_USE_SEGGER_RTT=y
+CONFIG_RTT_CONSOLE=y
+CONFIG_LOG_BACKEND_RTT=y
+
+### Shell over RTT
+CONFIG_SHELL_BACKEND_RTT=y
+CONFIG_SHELL_BACKEND_RTT_BUFFER=1
+
+CONFIG_UART_CONSOLE=n
+CONFIG_LOG_BACKEND_UART=n
+
+### RTT Buffer
+CONFIG_SEGGER_RTT_BUFFER_SIZE_UP=8192

firmware/debug_uart.conf

@@ -0,0 +1,10 @@
+### Debug transport: UART
+CONFIG_CONSOLE=y
+CONFIG_UART_CONSOLE=y
+CONFIG_LOG_BACKEND_UART=y
+
+### Shell over UART
+CONFIG_SHELL_BACKEND_SERIAL=y
+
+CONFIG_RTT_CONSOLE=n
+CONFIG_LOG_BACKEND_RTT=n

firmware/fs/build_lfs_audio.py

@@ -244,8 +244,10 @@ def main() -> None:
     if staging_root.exists():
         shutil.rmtree(staging_root)
 
-    out_sys = staging_root / "lfs" / "sys"
+    # The LittleFS partition is mounted at /lfs in firmware, so image root
-    out_a = staging_root / "lfs" / "a"
+    # must contain /sys and /a directly (not /lfs/sys and /lfs/a).
+    out_sys = staging_root / "sys"
+    out_a = staging_root / "a"
     out_sys.mkdir(parents=True, exist_ok=True)
     out_a.mkdir(parents=True, exist_ok=True)
 

firmware/fs/program.bat

@@ -1 +1 @@
-nrfutil device --x-ext-mem-config-file "%~dp0buzzy.json" program --firmware "%~dp0lfs_external_flash.hex" --options verify=VERIFY_READ,reset=RESET_SYSTEM
+nrfutil device --x-ext-mem-config-file "%~dp0buzzy.json" program --firmware "%~dp0lfs_external_flash.hex" --options chip_erase_mode=ERASE_NONE,verify=VERIFY_READ,reset=RESET_SYSTEM,ext_mem_erase_mode=ERASE_RANGES_TOUCHED_BY_FIRMWARE

firmware/fs/program.sh

@@ -1,4 +1,4 @@
 #!/usr/bin/env sh
 SCRIPT_DIR="$(CDPATH= cd -- "$(dirname -- "$0")" && pwd)"
 
-nrfutil device --x-ext-mem-config-file "$SCRIPT_DIR/buzzy.json" program --firmware "$SCRIPT_DIR/lfs_external_flash.hex" --options verify=VERIFY_READ,reset=RESET_SYSTEM
+nrfutil device --x-ext-mem-config-file "$SCRIPT_DIR/buzzy.json" program --firmware "$SCRIPT_DIR/lfs_external_flash.hex" --options chip_erase_mode=ERASE_NONE,verify=VERIFY_READ,reset=RESET_SYSTEM,ext_mem_erase_mode=ERASE_RANGES_TOUCHED_BY_FIRMWARE

firmware/libs/CMakeLists.txt

@@ -1,6 +1,9 @@
+add_subdirectory(settings_mgmt)
 add_subdirectory(fw_mgmt)
 add_subdirectory(fs_mgmt)
 add_subdirectory(ble_mgmt)
 add_subdirectory(buzz_proto)
 add_subdirectory(audio)
 add_subdirectory(event_mgmt)
+add_subdirectory(batt_mgmt)
+add_subdirectory(usb_mgmt)

firmware/libs/Kconfig

@@ -1,6 +1,9 @@
+rsource "settings_mgmt/Kconfig"
 rsource "fw_mgmt/Kconfig"
 rsource "fs_mgmt/Kconfig"
 rsource "ble_mgmt/Kconfig"
 rsource "buzz_proto/Kconfig"
 rsource "audio/Kconfig"
 rsource "event_mgmt/Kconfig"
+rsource "batt_mgmt/Kconfig"
+rsource "usb_mgmt/Kconfig"

firmware/libs/audio/src/audio.c

@@ -89,6 +89,15 @@ static void audio_set_state(enum audio_thread_state_t new_state, const char *rea
 {
     enum audio_thread_state_t old_state = atomic_get(&thread_state);
 
+    if ((old_state == AUDIO_IDLE) && (new_state != AUDIO_IDLE))
+    {
+        event_mgmt_set_event(EVENT_MGMT_AUDIO_ACTIVE);
+    }
+    else if ((old_state != AUDIO_IDLE) && (new_state == AUDIO_IDLE))
+    {
+        event_mgmt_set_event(EVENT_MGMT_AUDIO_IDLE);
+    }
+
     if (old_state != new_state)
     {
         LOG_INF("Audio state %s -> %s (%s)",

firmware/libs/batt_mgmt/CMakeLists.txt

@@ -0,0 +1,5 @@
+if(CONFIG_BATT_MGMT)
+  zephyr_library()
+  zephyr_library_sources(src/batt_mgmt.c)
+  zephyr_include_directories(include)
+endif()

firmware/libs/batt_mgmt/Kconfig

@@ -0,0 +1,96 @@
+menuconfig BATT_MGMT
+    bool "Battery Management"
+    default y
+    select ADC
+    select EVENT_MGMT
+    select GPIO
+    select USB_MGMT
+    select NRFX_SAADC
+    help
+      Library for initializing and managing the battery subsystem.
+
+if BATT_MGMT
+    config BATT_MGMT_EMPTY_THRESHOLD
+        int "Battery Empty Voltage (mV)"
+        default 3400
+        help
+          Voltage threshold treated as empty battery level (0/5).
+
+    config BATT_MGMT_SHUTDOWN_THRESHOLD
+        int "Critical shutdown voltage (mV)"
+        default 3300
+        help
+          If measured battery voltage is less than or equal to this threshold,
+          the device will power off to protect the battery.
+
+    config BATT_MGMT_FULL_THRESHOLD
+        int "Battery Full Voltage (mV)"
+        default 3980
+        help
+          Set the voltage level (in millivolts) that represents a full battery. Default is 3980 mV.
+    
+    config BATT_MGMT_80P_THRESHOLD
+        int "Battery 80% Voltage (mV)"
+        default 3820
+        help
+          Set the voltage level (in millivolts) that represents 80% battery. Default is 3820 mV.
+    
+    config BATT_MGMT_50P_THRESHOLD
+        int "Battery 50% Voltage (mV)"
+        default 3720
+        help
+          Set the voltage level (in millivolts) that represents 50% battery. Default is 3720 mV.
+
+    config BATT_MGMT_20P_THRESHOLD
+        int "Battery 20% Voltage (mV)"
+        default 3620
+        help
+          Set the voltage level (in millivolts) that represents 20% battery. Default is 3620 mV.
+
+    config BATT_MGMT_CHG_BLINKING_WINDOW_MS
+        int "Charger blinking detection window (ms)"
+        default 700
+        help
+          Time window to detect charger pin blinking (state changes). If the pin state
+          changes within this window, it's considered blinking (error state).
+
+    config BATT_MGMT_STANDBY_MEASURE_INTERVAL_MIN
+        int "Standby measurement interval (minutes)"
+        default 360
+        help
+          Measurement interval while idle in standby (no charging, no BLE, no audio).
+
+    config BATT_MGMT_ACTIVE_MEASURE_INTERVAL_MIN
+        int "Active measurement interval (minutes)"
+        default 1
+        help
+          Measurement interval while charging or BLE connected.
+
+    config BATT_MGMT_AUDIO_COOLDOWN_SEC
+        int "Audio cooldown before next measure (seconds)"
+        default 60
+        help
+          Delay before restarting periodic battery measurement after audio playback ends.
+
+    config BATT_MGMT_MONITOR_THREAD_STACK_SIZE
+        int "Battery monitor thread stack size"
+        default 1024
+        help
+          Stack size for the USB-triggered charger status monitor thread.
+
+    config BATT_MGMT_MONITOR_THREAD_PRIORITY
+        int "Battery monitor thread priority"
+        default 7
+        help
+          Cooperative priority for the monitor thread (lower number = higher priority).
+
+    config BATT_MGMT_BLINK_INTERVAL_LOGGING
+        bool "Enable logging of charger pin blinking intervals"
+        default n
+        help
+          If enabled, logs the time intervals between charger pin state changes, which can help diagnose charger connection issues.
+
+    module = BATT_MGMT
+    module-str = batt_mgmt
+    source "subsys/logging/Kconfig.template.log_config"
+endif # BATT_MGMT

firmware/libs/batt_mgmt/include/batt_mgmt.h

@@ -0,0 +1,107 @@
+#ifndef BATT_MGMT_H
+#define BATT_MGMT_H
+
+#include <zephyr/types.h>
+#include <stdbool.h>
+
+#define BATT_MGMT_OVERSAMPLING_8X 8U
+#define BATT_MGMT_OVERSAMPLING_16X 16U
+
+typedef enum {
+	BATT_STATE_DISCHARGING = 0x00,
+	BATT_STATE_FULL= 0x01,
+	BATT_STATE_CHARGING = 0x02,
+	BATT_STATE_ERROR = 0x03,
+	BATT_STATE_UNKNOWN = 0x04,
+} batt_mgmt_state_t;
+
+typedef struct {
+	batt_mgmt_state_t state;
+	uint8_t level;
+	uint8_t percent;
+	int32_t voltage_mv;
+} batt_mgmt_info_t;
+
+/**
+ * @brief Measure battery VDDH voltage.
+ *
+ * @param oversampling Oversampling factor (BATT_MGMT_OVERSAMPLING_8X or BATT_MGMT_OVERSAMPLING_16X).
+ * @param vddh_mv Pointer to store the result in millivolts.
+ * @return 0 on success, negative errno on failure.
+ */
+int batt_mgmt_measure_vddh_mv(uint8_t oversampling, int32_t *vddh_mv);
+
+/**
+ * @brief Get display voltage in millivolts.
+ *
+ * Returns the voltage value intended for UI/protocol display. Currently this is
+ * the latest measured VDDH value cached by batt_mgmt.
+ *
+ * @param vddh_mv Pointer receiving display voltage in mV.
+ * @return 0 on success, negative errno on failure.
+ */
+int batt_mgmt_get_display_voltage_mv(int32_t *vddh_mv);
+
+/**
+ * @brief Get battery level bucket (0..4) from configured thresholds.
+ *
+ * Level mapping:
+ * - 0: below 20% threshold
+ * - 1: 20%..49%
+ * - 2: 50%..79%
+ * - 3: 80%..99%
+ * - 4: full and above
+ *
+ * @param level Pointer receiving level in range 0..4.
+ * @return 0 on success, negative errno on failure.
+ */
+int batt_mgmt_get_battery_level(uint8_t *level);
+
+/**
+ * @brief Get battery percentage (0-100) from configured voltage thresholds.
+ *
+ * Uses piecewise linear interpolation over:
+ * - EMPTY..20%
+ * - 20%..50%
+ * - 50%..80%
+ * - 80%..FULL
+ *
+ * @param percent Pointer receiving percentage in range 0..100.
+ * @return 0 on success, negative errno on failure.
+ */
+int batt_mgmt_get_battery_percent(uint8_t *percent);
+
+/**
+ * @brief Get raw charger status (GPIO level).
+ *
+ * Returns the current logic level of the charger status pin (typically from ETA6003).
+ * This is the **raw GPIO status**, not a processed state machine result.
+ *
+ * @return true if charger pin is high (e.g., battery is "charging"), false if low.
+ */
+bool batt_mgmt_get_charger_status(void);
+
+/**
+ * @brief Get processed battery state with blinking detection.
+ *
+ * Returns a derived state based on:
+ * - USB VBUS presence (from usb_mgmt)
+ * - Charger status GPIO level (from batt_mgmt_get_charger_status)
+ * - Blinking detection (state changes within CONFIG_BATT_MGMT_CHG_BLINKING_WINDOW_MS)
+ *
+ * Note: This differs from batt_mgmt_get_charger_status() which returns the **raw** GPIO level.
+ *
+ * @return Battery state enum (DISCHARGING, FULL, CHARGING, or ERROR if blinking detected).
+ */
+batt_mgmt_state_t batt_mgmt_get_battery_state(void);
+
+/**
+ * @brief Get all battery information in one call.
+ *
+ * @param info Pointer receiving state, level (0..4), percent (0..100), and voltage in mV.
+ * @return 0 on success, negative errno on failure.
+ */
+int batt_mgmt_get_info(batt_mgmt_info_t *info);
+
+#endif
+

firmware/libs/batt_mgmt/src/batt_mgmt.c

@@ -0,0 +1,591 @@
+#include <zephyr/device.h>
+#include <zephyr/drivers/adc.h>
+#include <zephyr/drivers/gpio.h>
+#include <zephyr/init.h>
+#include <zephyr/kernel.h>
+#include <zephyr/logging/log.h>
+#include <nrfx_saadc.h>
+
+#include <errno.h>
+#include <stdbool.h>
+
+#include "batt_mgmt.h"
+#include "usb_mgmt.h"
+
+LOG_MODULE_REGISTER(batt_mgmt, CONFIG_BATT_MGMT_LOG_LEVEL);
+
+#define BATT_VDDH_DIVIDER_FACTOR 5
+
+#define BATT_VDDH_ADC_NODE DT_PATH(zephyr_user)
+static const struct adc_dt_spec batt_vddh_adc = ADC_DT_SPEC_GET_BY_NAME(BATT_VDDH_ADC_NODE, vddh);
+
+#define BATT_CHG_STATUS_NODE DT_ALIAS(chg_status)
+static const struct gpio_dt_spec batt_chg_status = GPIO_DT_SPEC_GET(BATT_CHG_STATUS_NODE, gpios);
+
+static bool batt_mgmt_ready;
+static int64_t batt_mgmt_last_chg_change_ms;
+static int64_t batt_mgmt_last_offset_calib_ms;
+static int32_t batt_mgmt_last_vddh_mv;
+static bool batt_mgmt_chg_interrupt_enabled;
+static K_THREAD_STACK_DEFINE(batt_monitor_stack, CONFIG_BATT_MGMT_MONITOR_THREAD_STACK_SIZE);
+static struct k_thread batt_monitor_thread_data;
+static struct k_sem batt_mgmt_saadc_calib_sem;
+static int batt_mgmt_saadc_calib_rc;
+
+static void batt_mgmt_saadc_calib_handler(nrfx_saadc_evt_t const *p_event)
+{
+	if ((p_event == NULL) || (p_event->type != NRFX_SAADC_EVT_CALIBRATEDONE))
+	{
+		batt_mgmt_saadc_calib_rc = -EIO;
+	}
+	else
+	{
+		batt_mgmt_saadc_calib_rc = 0;
+	}
+
+	k_sem_give(&batt_mgmt_saadc_calib_sem);
+}
+
+static int batt_mgmt_calibrate_offset_if_needed(bool force)
+{
+	int rc;
+	int64_t now_ms = k_uptime_get();
+	int64_t calib_interval_ms = (int64_t)CONFIG_BATT_MGMT_STANDBY_MEASURE_INTERVAL_MIN * 60 * 1000;
+
+	if (!force && (now_ms - batt_mgmt_last_offset_calib_ms < calib_interval_ms))
+	{
+		return 0;
+	}
+
+	while (k_sem_take(&batt_mgmt_saadc_calib_sem, K_NO_WAIT) == 0)
+	{
+	}
+
+	batt_mgmt_saadc_calib_rc = -EIO;
+	rc = nrfx_saadc_offset_calibrate(batt_mgmt_saadc_calib_handler);
+	if (rc < 0)
+	{
+		return rc;
+	}
+
+	rc = k_sem_take(&batt_mgmt_saadc_calib_sem, K_MSEC(100));
+	if (rc < 0)
+	{
+		return rc;
+	}
+
+	if (batt_mgmt_saadc_calib_rc < 0)
+	{
+		return batt_mgmt_saadc_calib_rc;
+	}
+
+	batt_mgmt_last_offset_calib_ms = k_uptime_get();
+	return 0;
+}
+
+static int batt_mgmt_to_adc_oversampling(uint8_t oversampling, uint8_t *adc_oversampling)
+{
+	if (adc_oversampling == NULL)
+	{
+		return -EINVAL;
+	}
+
+	switch (oversampling)
+	{
+	case BATT_MGMT_OVERSAMPLING_8X:
+		*adc_oversampling = 3U;
+		return 0;
+	case BATT_MGMT_OVERSAMPLING_16X:
+		*adc_oversampling = 4U;
+		return 0;
+	default:
+		return -EINVAL;
+	}
+}
+
+int batt_mgmt_measure_vddh_mv(uint8_t oversampling, int32_t *vddh_mv)
+{
+	int rc;
+	uint8_t adc_oversampling;
+	int16_t raw_sample;
+	int32_t input_mv;
+	struct adc_sequence sequence = {
+		.buffer = &raw_sample,
+		.buffer_size = sizeof(raw_sample),
+	};
+
+	if (vddh_mv == NULL)
+	{
+		return -EINVAL;
+	}
+
+	if (!batt_mgmt_ready)
+	{
+		return -EAGAIN;
+	}
+
+	rc = batt_mgmt_calibrate_offset_if_needed(false);
+	if (rc < 0)
+	{
+		LOG_WRN("ADC offset calibration failed before measurement: %d", rc);
+	}
+
+	rc = batt_mgmt_to_adc_oversampling(oversampling, &adc_oversampling);
+	if (rc < 0)
+	{
+		return rc;
+	}
+
+	rc = adc_sequence_init_dt(&batt_vddh_adc, &sequence);
+	if (rc < 0)
+	{
+		return rc;
+	}
+
+	sequence.oversampling = adc_oversampling;
+
+	rc = adc_read_dt(&batt_vddh_adc, &sequence);
+	if (rc < 0)
+	{
+		return rc;
+	}
+
+	input_mv = raw_sample;
+	rc = adc_raw_to_millivolts_dt(&batt_vddh_adc, &input_mv);
+	if (rc < 0)
+	{
+		return rc;
+	}
+
+	*vddh_mv = input_mv * BATT_VDDH_DIVIDER_FACTOR;
+	batt_mgmt_last_vddh_mv = *vddh_mv;
+
+	LOG_DBG("Battery VDDH: %d mV (raw=%d, os=%ux)", *vddh_mv, raw_sample, oversampling);
+	return 0;
+}
+
+static int batt_mgmt_linear_percent(int32_t mv, int32_t lo_mv, int32_t hi_mv,
+									uint8_t lo_pct, uint8_t hi_pct, uint8_t *out_pct)
+{
+	int32_t num;
+	int32_t den;
+	int32_t pct;
+
+	if (out_pct == NULL)
+	{
+		return -EINVAL;
+	}
+
+	if (hi_mv <= lo_mv)
+	{
+		return -EINVAL;
+	}
+
+	if (mv <= lo_mv)
+	{
+		*out_pct = lo_pct;
+		return 0;
+	}
+
+	if (mv >= hi_mv)
+	{
+		*out_pct = hi_pct;
+		return 0;
+	}
+
+	num = (mv - lo_mv) * (int32_t)(hi_pct - lo_pct);
+	den = hi_mv - lo_mv;
+	pct = (int32_t)lo_pct + (num / den);
+
+	if (pct < 0)
+	{
+		pct = 0;
+	}
+	else if (pct > 100)
+	{
+		pct = 100;
+	}
+
+	*out_pct = (uint8_t)pct;
+	return 0;
+}
+
+int batt_mgmt_get_display_voltage_mv(int32_t *vddh_mv)
+{
+	int rc;
+
+	if (vddh_mv == NULL)
+	{
+		return -EINVAL;
+	}
+
+	if (!batt_mgmt_ready)
+	{
+		return -EAGAIN;
+	}
+
+	if (batt_mgmt_last_vddh_mv <= 0)
+	{
+		rc = batt_mgmt_measure_vddh_mv(BATT_MGMT_OVERSAMPLING_16X, &batt_mgmt_last_vddh_mv);
+		if (rc < 0)
+		{
+			return rc;
+		}
+	}
+
+	*vddh_mv = batt_mgmt_last_vddh_mv;
+	return 0;
+}
+
+int batt_mgmt_get_battery_level(uint8_t *level)
+{
+	int32_t mv;
+	int rc;
+
+	if (level == NULL)
+	{
+		return -EINVAL;
+	}
+
+	rc = batt_mgmt_get_display_voltage_mv(&mv);
+	if (rc < 0)
+	{
+		return rc;
+	}
+
+	if (mv >= CONFIG_BATT_MGMT_FULL_THRESHOLD)
+	{
+		*level = 4U;
+	}
+	else if (mv >= CONFIG_BATT_MGMT_80P_THRESHOLD)
+	{
+		*level = 3U;
+	}
+	else if (mv >= CONFIG_BATT_MGMT_50P_THRESHOLD)
+	{
+		*level = 2U;
+	}
+	else if (mv >= CONFIG_BATT_MGMT_20P_THRESHOLD)
+	{
+		*level = 1U;
+	}
+	else
+	{
+		*level = 0U;
+	}
+
+	return 0;
+}
+
+int batt_mgmt_get_battery_percent(uint8_t *percent)
+{
+	int32_t mv;
+	int rc;
+
+	if (percent == NULL)
+	{
+		return -EINVAL;
+	}
+
+	rc = batt_mgmt_get_display_voltage_mv(&mv);
+	if (rc < 0)
+	{
+		return rc;
+	}
+
+	if (mv <= CONFIG_BATT_MGMT_EMPTY_THRESHOLD)
+	{
+		*percent = 0;
+		return 0;
+	}
+
+	if (mv >= CONFIG_BATT_MGMT_FULL_THRESHOLD)
+	{
+		*percent = 100;
+		return 0;
+	}
+
+	if (mv < CONFIG_BATT_MGMT_20P_THRESHOLD)
+	{
+		return batt_mgmt_linear_percent(mv,
+								CONFIG_BATT_MGMT_EMPTY_THRESHOLD,
+								CONFIG_BATT_MGMT_20P_THRESHOLD,
+								0, 20, percent);
+	}
+
+	if (mv < CONFIG_BATT_MGMT_50P_THRESHOLD)
+	{
+		return batt_mgmt_linear_percent(mv,
+								CONFIG_BATT_MGMT_20P_THRESHOLD,
+								CONFIG_BATT_MGMT_50P_THRESHOLD,
+								20, 50, percent);
+	}
+
+	if (mv < CONFIG_BATT_MGMT_80P_THRESHOLD)
+	{
+		return batt_mgmt_linear_percent(mv,
+								CONFIG_BATT_MGMT_50P_THRESHOLD,
+								CONFIG_BATT_MGMT_80P_THRESHOLD,
+								50, 80, percent);
+	}
+
+	return batt_mgmt_linear_percent(mv,
+							CONFIG_BATT_MGMT_80P_THRESHOLD,
+							CONFIG_BATT_MGMT_FULL_THRESHOLD,
+							80, 100, percent);
+}
+
+static void batt_mgmt_chg_interrupt_handler(const struct device *dev,
+											struct gpio_callback *cb,
+											uint32_t pins)
+{
+	int64_t now_ms = k_uptime_get();
+	ARG_UNUSED(dev);
+	ARG_UNUSED(cb);
+	ARG_UNUSED(pins);
+
+#ifdef CONFIG_BATT_MGMT_BLINK_INTERVAL_LOGGING
+	int64_t delta_ms = now_ms - batt_mgmt_last_chg_change_ms;
+	LOG_DBG("CHG interrupt: delta=%lld ms", delta_ms);
+#endif
+
+	batt_mgmt_last_chg_change_ms = now_ms;
+}
+
+static int batt_mgmt_enable_chg_interrupt(void)
+{
+	int rc;
+	static struct gpio_callback batt_chg_cb;
+
+	if (batt_mgmt_chg_interrupt_enabled)
+	{
+		return 0;
+	}
+
+	if (!gpio_is_ready_dt(&batt_chg_status))
+	{
+		LOG_ERR("CHG GPIO device not ready");
+		return -ENODEV;
+	}
+
+	rc = gpio_pin_configure_dt(&batt_chg_status, GPIO_INPUT);
+	if (rc < 0)
+	{
+		LOG_ERR("Failed to configure CHG GPIO: %d", rc);
+		return rc;
+	}
+
+	gpio_init_callback(&batt_chg_cb, batt_mgmt_chg_interrupt_handler, BIT(batt_chg_status.pin));
+	rc = gpio_add_callback(batt_chg_status.port, &batt_chg_cb);
+	if (rc < 0)
+	{
+		LOG_ERR("Failed to add CHG callback: %d", rc);
+		return rc;
+	}
+
+	rc = gpio_pin_interrupt_configure_dt(&batt_chg_status, GPIO_INT_EDGE_BOTH);
+	if (rc < 0)
+	{
+		LOG_ERR("Failed to configure CHG interrupt: %d", rc);
+		return rc;
+	}
+
+	batt_mgmt_chg_interrupt_enabled = true;
+	batt_mgmt_last_chg_change_ms = k_uptime_get();
+	LOG_INF("CHG interrupt enabled");
+
+	return 0;
+}
+
+static int batt_mgmt_disable_chg_interrupt(void)
+{
+	int rc;
+
+	if (!batt_mgmt_chg_interrupt_enabled)
+	{
+		return 0;
+	}
+
+	rc = gpio_pin_interrupt_configure_dt(&batt_chg_status, GPIO_INT_DISABLE);
+	if (rc < 0)
+	{
+		LOG_WRN("Failed to disable CHG interrupt: %d", rc);
+		return rc;
+	}
+
+	rc = gpio_pin_configure(batt_chg_status.port, batt_chg_status.pin, GPIO_DISCONNECTED);
+	if (rc < 0)
+	{
+		LOG_WRN("Failed to disconnect CHG GPIO: %d", rc);
+		return rc;
+	}
+
+	batt_mgmt_chg_interrupt_enabled = false;
+	LOG_DBG("CHG interrupt disabled");
+
+	return 0;
+}
+
+bool batt_mgmt_get_charger_status(void)
+{
+	if (!batt_mgmt_chg_interrupt_enabled)
+	{
+		return false;
+	}
+
+	return gpio_pin_get_dt(&batt_chg_status);
+}
+
+batt_mgmt_state_t batt_mgmt_get_battery_state(void)
+{
+	int64_t now_ms = k_uptime_get();
+	int64_t delta_ms = now_ms - batt_mgmt_last_chg_change_ms;
+	bool chg_high = batt_mgmt_get_charger_status();
+	bool usb_present = usb_mgmt_is_vbus_present();
+
+	/* Blinking detection: state change within window */
+	if (delta_ms < CONFIG_BATT_MGMT_CHG_BLINKING_WINDOW_MS)
+	{
+		LOG_DBG("Blinking detected (delta=%lld ms)", delta_ms);
+		return BATT_STATE_ERROR;
+	}
+
+	/* Stable states */
+	if (chg_high)
+	{
+		return BATT_STATE_CHARGING;
+	}
+
+	if (usb_present)
+	{
+		return BATT_STATE_FULL;
+	}
+
+	return BATT_STATE_DISCHARGING;
+}
+
+int batt_mgmt_get_info(batt_mgmt_info_t *info)
+{
+	int rc;
+
+	if (info == NULL)
+	{
+		return -EINVAL;
+	}
+
+	rc = batt_mgmt_get_display_voltage_mv(&info->voltage_mv);
+	if (rc < 0)
+	{
+		return rc;
+	}
+
+	rc = batt_mgmt_get_battery_level(&info->level);
+	if (rc < 0)
+	{
+		return rc;
+	}
+
+	rc = batt_mgmt_get_battery_percent(&info->percent);
+	if (rc < 0)
+	{
+		return rc;
+	}
+
+	info->state = batt_mgmt_get_battery_state();
+	return 0;
+}
+
+static void batt_mgmt_monitor_thread(void *unused1, void *unused2, void *unused3)
+{
+	(void)unused1;
+	(void)unused2;
+	(void)unused3;
+
+	if (!usb_mgmt_wait_ready(K_SECONDS(2)))
+	{
+		LOG_WRN("usb_mgmt not ready after timeout; using current VBUS state");
+	}
+
+	/* Sync initial state in case VBUS was already present before this thread started. */
+	bool vbus_present = usb_mgmt_is_vbus_present();
+
+	if (vbus_present)
+	{
+		(void)batt_mgmt_enable_chg_interrupt();
+	}
+	else
+	{
+		(void)batt_mgmt_disable_chg_interrupt();
+	}
+
+	while (1)
+	{
+		uint32_t events = k_event_wait(&usb_mgmt_events,
+									   USB_MGMT_VBUS_CONNECTED | USB_MGMT_VBUS_DISCONNECTED,
+									   false, K_FOREVER);
+
+		if (events & USB_MGMT_VBUS_CONNECTED)
+		{
+			(void)batt_mgmt_enable_chg_interrupt();
+		}
+
+		if (events & USB_MGMT_VBUS_DISCONNECTED)
+		{
+			(void)batt_mgmt_disable_chg_interrupt();
+		}
+
+		k_event_clear(&usb_mgmt_events, USB_MGMT_VBUS_CONNECTED | USB_MGMT_VBUS_DISCONNECTED);
+	}
+}
+
+static int batt_mgmt_init(void)
+{
+	int32_t boot_vddh_mv;
+	int rc;
+
+	if (!adc_is_ready_dt(&batt_vddh_adc))
+	{
+		LOG_ERR("VDDH ADC device not ready");
+		return -ENODEV;
+	}
+
+	rc = adc_channel_setup_dt(&batt_vddh_adc);
+	if (rc < 0)
+	{
+		LOG_ERR("VDDH ADC channel setup failed: %d", rc);
+		return rc;
+	}
+
+	k_sem_init(&batt_mgmt_saadc_calib_sem, 0, 1);
+	batt_mgmt_last_offset_calib_ms = 0;
+
+	batt_mgmt_ready = true;
+
+	rc = batt_mgmt_calibrate_offset_if_needed(true);
+	if (rc < 0)
+	{
+		LOG_WRN("Initial ADC offset calibration failed: %d", rc);
+	}
+
+	rc = batt_mgmt_measure_vddh_mv(BATT_MGMT_OVERSAMPLING_16X, &boot_vddh_mv);
+	if (rc < 0)
+	{
+		LOG_WRN("Initial battery measurement failed: %d", rc);
+		return 0;
+	}
+
+	batt_mgmt_last_vddh_mv = boot_vddh_mv;
+	LOG_DBG("Initial battery VDDH: %d mV", boot_vddh_mv);
+
+	k_thread_create(&batt_monitor_thread_data,
+					batt_monitor_stack,
+					K_THREAD_STACK_SIZEOF(batt_monitor_stack),
+					batt_mgmt_monitor_thread,
+					NULL, NULL, NULL,
+					K_PRIO_COOP(CONFIG_BATT_MGMT_MONITOR_THREAD_PRIORITY),
+					0, K_NO_WAIT);
+
+	return 0;
+}
+
+SYS_INIT(batt_mgmt_init, APPLICATION, CONFIG_APPLICATION_INIT_PRIORITY);

firmware/libs/ble_mgmt/Kconfig

@@ -3,88 +3,39 @@ menuconfig BLE_MGMT
     default n
     select BT
     select BT_PERIPHERAL
-    select BT_LOG_LEVEL_WARN
     select BT_DEVICE_NAME_DYNAMIC
     help
-      Library for initializing and managing Bluetooth functionality.
+      Minimal BLE transport for the buzzer firmware.
 
 if BLE_MGMT
-    config BLE_MGMT_TX_QUEUE_DEPTH
-        int "BLE TX queue depth"
-        default 32
-        help
-          Number of notification payloads that can be queued in the BLE transport.
-
     config BLE_MGMT_DEFAULT_DEVICE_NAME
-        string "Default Bluetooth Device Name"
+        string "Default Bluetooth device name"
-        default "Edis Buzzer"
+        default "Edis Buzzer 2.0"
-    config BLE_MGMT_ADV_INT_MIN
-        int "Minimum Advertising Interval (in 0.625 ms units)"
-        default 160
         help
-               Minimal advertising interval. 160 equals to 100ms.
+          Device name used when ble_mgmt_init() is called with a NULL name.
-    config BLE_MGMT_ADV_INT_MAX
-        int "Maximum Advertising Interval (ms)"
-        default 160
-            help
-               Maximal advertising interval. 160 equals to 100ms.
 
-    # Airtime 
-    config BT_CTLR_SDC_MAX_CONN_EVENT_LEN_DEFAULT
-        default 4000000
-    
-    # MTU Setup
-    config BT_BUF_ACL_RX_SIZE
-        default 502
-    config BT_BUF_ACL_TX_SIZE
-        default 502
-    config BT_L2CAP_TX_MTU
-        default 498
-    config BT_CTLR_DATA_LENGTH_MAX
-        default 251
-
-    # Buffers
-    config BT_BUF_ACL_TX_COUNT
-        default 15
-    config BT_L2CAP_TX_BUF_COUNT
-        default 15
-    config BT_CONN_TX_MAX
-        default 15
-    config BT_CTLR_SDC_TX_PACKET_COUNT
-        default 15
-    config BT_CTLR_SDC_RX_PACKET_COUNT
-        default 15
-    config BT_BUF_EVT_RX_COUNT
-        default 16
-    
-    # Callbacks
-    config BT_USER_PHY_UPDATE
-        default y
-    config BT_USER_DATA_LEN_UPDATE
-        default y
-
-    # Automatic updates
-    config BT_AUTO_PHY_UPDATE
-        default y
-    config BT_AUTO_DATA_LEN_UPDATE
-        default y
-    config BT_GAP_AUTO_UPDATE_CONN_PARAMS
-        default y
-
-    # Preferred defaults
-    config BT_PERIPHERAL_PREF_MIN_INT
-        default 6
-    config BT_PERIPHERAL_PREF_MAX_INT
-        default 40
-    config BT_PERIPHERAL_PREF_LATENCY
-        default 0
-    config BT_PERIPHERAL_PREF_TIMEOUT
-        default 400
-
-    # Connections
     config BT_MAX_CONN
         default 2
 
+    # BLE control/data handling runs in BT RX workqueue. Enforce a larger
+    # stack while BLE_MGMT is enabled to avoid overflows on connect/file ops.
+    config BT_RX_STACK_SIZE
+        range 3072 8192
+        default 3072
+
+    # Use larger BLE data path buffers for file transfer use-cases.
+    config BT_L2CAP_TX_MTU
+        default 498
+
+    config BT_BUF_ACL_RX_SIZE
+        default 502
+
+    config BT_BUF_ACL_TX_SIZE
+        default 502
+
+    config BT_CTLR_DATA_LENGTH_MAX
+        default 251
+        
     module = BLE_MGMT
     module-str = ble_mgmt
     source "subsys/logging/Kconfig.template.log_config"

firmware/libs/ble_mgmt/include/ble_mgmt.h

@@ -17,7 +17,8 @@ int ble_mgmt_init(ble_mgmt_rx_cb_t rx_cb, const char *device_name);
  * Sends data to the connected central device via a GATT characteristic.
  * @param data Pointer to the data buffer to send.
  * @param len Length of the data in bytes.
- * @return 0 on success, -EACCES if notifications are not enabled, or a negative error code on failure.
+ * @return 0 on success, -EAGAIN if no ATT link is ready yet, -EACCES if notifications are not enabled,
+ *         or a negative error code on failure.
  */
 int ble_mgmt_send(const uint8_t *data, uint16_t len);
 

firmware/libs/ble_mgmt/src/ble_mgmt.c

@@ -1,15 +1,16 @@
-#include <zephyr/bluetooth/bluetooth.h>
+#include <errno.h>
-#include <zephyr/bluetooth/hci.h>
-#include <zephyr/bluetooth/conn.h>
-#include <zephyr/bluetooth/uuid.h>
-#include <zephyr/bluetooth/gatt.h>
-#include <zephyr/logging/log.h>
-#include <zephyr/bluetooth/gatt.h>
-#include <zephyr/bluetooth/conn.h>
-
 #include <string.h>
 
+#include <zephyr/kernel.h>
+#include <zephyr/bluetooth/bluetooth.h>
+#include <zephyr/bluetooth/conn.h>
+#include <zephyr/bluetooth/gatt.h>
+#include <zephyr/bluetooth/hci.h>
+#include <zephyr/bluetooth/uuid.h>
+#include <zephyr/logging/log.h>
+
 #include "ble_mgmt.h"
+#include "event_mgmt.h"
 
 LOG_MODULE_REGISTER(ble_mgmt, CONFIG_BLE_MGMT_LOG_LEVEL);
 
@@ -20,18 +21,24 @@ LOG_MODULE_REGISTER(ble_mgmt, CONFIG_BLE_MGMT_LOG_LEVEL);
 #define BUZZ_TX_UUID_VAL \
     BT_UUID_128_ENCODE(0xe517d988, 0xbab5, 0x4574, 0x8479, 0x97c6cb115ca2)
 
+#define DEFAULT_ATT_MTU 23U
+#define GATT_NOTIFY_OVERHEAD 3U
+#define MAX_ADV_NAME_LEN 29
+
+struct ble_peer {
+    struct bt_conn *conn;
+};
+
 static struct bt_uuid_128 buzz_service_uuid = BT_UUID_INIT_128(BUZZ_SERVICE_UUID_VAL);
 static struct bt_uuid_128 buzz_rx_uuid = BT_UUID_INIT_128(BUZZ_RX_UUID_VAL);
 static struct bt_uuid_128 buzz_tx_uuid = BT_UUID_INIT_128(BUZZ_TX_UUID_VAL);
 
-static ble_mgmt_rx_cb_t app_rx_cb = NULL;
+static ble_mgmt_rx_cb_t app_rx_cb;
-static bool notify_enabled = false;
+static bool ble_ready;
-
+static bool advertising_active;
-static uint16_t current_tx_mtu = 23;
+static uint16_t current_att_mtu = DEFAULT_ATT_MTU;
-static uint16_t current_rx_mtu = 23;
-
-#define MAX_ADV_NAME_LEN 29
 static char current_device_name[MAX_ADV_NAME_LEN + 1];
+static struct ble_peer peers[CONFIG_BT_MAX_CONN];
 
 static const struct bt_data ad[] = {
     BT_DATA_BYTES(BT_DATA_FLAGS, (BT_LE_AD_GENERAL | BT_LE_AD_NO_BREDR)),
@@ -44,38 +51,155 @@ static struct bt_data sd[] = {
 
 static struct bt_le_adv_param adv_param = {
     .id = BT_ID_DEFAULT,
-    .sid = 0,
-    .secondary_max_skip = 0,
     .options = BT_LE_ADV_OPT_CONN,
-    .interval_min = CONFIG_BLE_MGMT_ADV_INT_MIN,
+    .interval_min = BT_GAP_ADV_FAST_INT_MIN_2,
-    .interval_max = CONFIG_BLE_MGMT_ADV_INT_MAX,
+    .interval_max = BT_GAP_ADV_FAST_INT_MAX_2,
-    .peer = NULL,
 };
 
 static void att_mtu_updated(struct bt_conn *conn, uint16_t tx, uint16_t rx)
 {
-    LOG_INF("MTU exchanged: TX %u bytes, RX %u bytes", tx, rx);
+    ARG_UNUSED(conn);
-    current_tx_mtu = tx;
+
-    current_rx_mtu = rx;
+    current_att_mtu = MIN(tx, rx);
+    LOG_INF("ATT MTU updated to %u", current_att_mtu);
+}
+
+static size_t peer_count(void)
+{
+    size_t count = 0;
+
+    for (size_t index = 0; index < ARRAY_SIZE(peers); ++index) {
+        if (peers[index].conn != NULL) {
+            ++count;
+        }
+    }
+
+    return count;
+}
+
+static struct ble_peer *find_peer(struct bt_conn *conn)
+{
+    for (size_t index = 0; index < ARRAY_SIZE(peers); ++index) {
+        if (peers[index].conn == conn) {
+            return &peers[index];
+        }
+    }
+
+    return NULL;
+}
+
+static struct ble_peer *reserve_peer(struct bt_conn *conn)
+{
+    struct ble_peer *peer = find_peer(conn);
+
+    if (peer != NULL) {
+        return peer;
+    }
+
+    for (size_t index = 0; index < ARRAY_SIZE(peers); ++index) {
+        if (peers[index].conn == NULL) {
+            peers[index].conn = bt_conn_ref(conn);
+            return &peers[index];
+        }
+    }
+
+    return NULL;
+}
+
+static void release_peer(struct bt_conn *conn)
+{
+    struct ble_peer *peer = find_peer(conn);
+
+    if (peer == NULL) {
+        return;
+    }
+
+    bt_conn_unref(peer->conn);
+    peer->conn = NULL;
+}
+
+static void set_device_name(const char *name)
+{
+    const char *name_to_use = name != NULL ? name : CONFIG_BLE_MGMT_DEFAULT_DEVICE_NAME;
+
+    strncpy(current_device_name, name_to_use, MAX_ADV_NAME_LEN);
+    current_device_name[MAX_ADV_NAME_LEN] = '\0';
+    sd[0].data_len = strlen(current_device_name);
+
+#ifdef CONFIG_BT_DEVICE_NAME_DYNAMIC
+    if (ble_ready) {
+        (void)bt_set_name(current_device_name);
+    }
+#endif
+}
+
+static int start_advertising(void)
+{
+    int rc;
+
+    if (!ble_ready || peer_count() >= CONFIG_BT_MAX_CONN || advertising_active) {
+        return 0;
+    }
+
+    rc = bt_le_adv_start(&adv_param, ad, ARRAY_SIZE(ad), sd, ARRAY_SIZE(sd));
+    if (rc == -EALREADY) {
+        advertising_active = true;
+        return 0;
+    }
+
+    if (rc != 0) {
+        LOG_ERR("Failed to start advertising (err %d)", rc);
+        return rc;
+    }
+
+    advertising_active = true;
+    LOG_INF("Advertising as %s", current_device_name);
+    return 0;
+}
+
+static int restart_advertising(void)
+{
+    int rc;
+
+    if (!ble_ready) {
+        return -EAGAIN;
+    }
+
+    if (advertising_active) {
+        rc = bt_le_adv_stop();
+        if ((rc != 0) && (rc != -EALREADY)) {
+            LOG_ERR("Failed to stop advertising (err %d)", rc);
+            return rc;
+        }
+
+        advertising_active = false;
+    }
+
+    return start_advertising();
 }
 
 static ssize_t rx_cb(struct bt_conn *conn, const struct bt_gatt_attr *attr,
                      const void *buf, uint16_t len, uint16_t offset, uint8_t flags)
 {
-    LOG_DBG("Received %u bytes", len);
+    ARG_UNUSED(conn);
-    LOG_HEXDUMP_DBG(buf, len, "Data:");
+    ARG_UNUSED(attr);
+    ARG_UNUSED(flags);
 
-    if (app_rx_cb)
+    if (offset != 0U) {
-    {
+        return BT_GATT_ERR(BT_ATT_ERR_INVALID_OFFSET);
+    }
+
+    if (app_rx_cb != NULL) {
         app_rx_cb((const uint8_t *)buf, len);
     }
+
     return len;
 }
 
 static void tx_ccc_cfg_changed(const struct bt_gatt_attr *attr, uint16_t value)
 {
-    notify_enabled = (value == BT_GATT_CCC_NOTIFY);
+    ARG_UNUSED(attr);
-    LOG_INF("Notifications %s", notify_enabled ? "enabled" : "disabled");
+    LOG_INF("Notification state changed: 0x%04x", value);
 }
 
 BT_GATT_SERVICE_DEFINE(ble_mgmt_svc,
@@ -86,177 +210,167 @@ BT_GATT_SERVICE_DEFINE(ble_mgmt_svc,
                            BT_GATT_PERM_NONE, NULL, NULL, NULL),
     BT_GATT_CCC(tx_ccc_cfg_changed, BT_GATT_PERM_READ | BT_GATT_PERM_WRITE));
 
-uint16_t ble_mgmt_get_max_payload(void)
-{
-    /* Kappe die verhandelte MTU auf die hart konfigurierte Zephyr-Puffergrenze */
-    uint16_t effective_mtu = MIN(current_tx_mtu, current_rx_mtu);
-
-#ifdef CONFIG_BT_L2CAP_TX_MTU
-    if (effective_mtu > CONFIG_BT_L2CAP_TX_MTU)
-    {
-        effective_mtu = CONFIG_BT_L2CAP_TX_MTU;
-    }
-#endif
-
-    /* 3 Bytes abziehen für den GATT Notification Overhead */
-    return (effective_mtu > 3) ? (effective_mtu - 3) : 20;
-}
-
-int ble_mgmt_send(const uint8_t *data, uint16_t len)
-{
-    if (!notify_enabled)
-    {
-        return -EACCES;
-    }
-    int rc;
-
-    do
-    {
-        rc = bt_gatt_notify(NULL, &ble_mgmt_svc.attrs[4], data, len);
-        if (rc == -ENOMEM)
-        {
-            k_sleep(K_MSEC(5)); // Thread pausieren, bis TX-Buffer frei wird
-        }
-    } while (rc == -ENOMEM);
-
-    if (rc)
-    {
-        LOG_ERR("Failed to send notification (err %d)", rc);
-        return rc;
-    }
-    return rc;
-}
-
-/* Interne Hilfsfunktion zur Zuweisung des Namens */
-static void set_device_name(const char *name)
-{
-    if (!name)
-    {
-        return;
-    }
-
-    strncpy(current_device_name, name, MAX_ADV_NAME_LEN);
-    current_device_name[MAX_ADV_NAME_LEN] = '\0';
-
-    /* Längen-Update im Scan-Response Array */
-    sd[0].data_len = strlen(current_device_name);
-
-#ifdef CONFIG_BT_DEVICE_NAME_DYNAMIC
-    /* Setzt den Namen parallel im Zephyr GAP-Service (wichtig für macOS) */
-    bt_set_name(current_device_name);
-#endif
-}
-
-int ble_mgmt_update_adv_name(const char *new_name)
-{
-    int rc;
-
-    bt_le_adv_stop();
-    set_device_name(new_name);
-
-    rc = bt_le_adv_start(&adv_param, ad, ARRAY_SIZE(ad), sd, ARRAY_SIZE(sd));
-    if (rc)
-    {
-        LOG_ERR("Advertising failed to restart after name update (err %d)", rc);
-        return rc;
-    }
-
-    LOG_INF("Advertising updated. New Name: %s", current_device_name);
-    return 0;
-}
-
 static void connected(struct bt_conn *conn, uint8_t err)
 {
-    if (err)
+    char addr_str[BT_ADDR_LE_STR_LEN];
-    {
+    struct bt_conn_info info;
+    int rc;
+
+    if (err != 0U) {
         LOG_ERR("Connection failed (err 0x%02x)", err);
         return;
     }
 
-    char addr_str[BT_ADDR_LE_STR_LEN];
+    advertising_active = false;
-    struct bt_conn_info info;
 
-    int rc = bt_conn_get_info(conn, &info);
+    if (reserve_peer(conn) == NULL) {
-    if (rc == 0)
+        LOG_ERR("No free BLE peer slot available");
-    {
+        return;
+    }
+
+    rc = bt_conn_get_info(conn, &info);
+    if ((rc == 0) && (info.type == BT_CONN_TYPE_LE)) {
         bt_addr_le_to_str(info.le.dst, addr_str, sizeof(addr_str));
-        LOG_INF("Connected to %s", addr_str);
+        LOG_INF("Connected to %s (%u/%u)", addr_str, (unsigned int)peer_count(),
-        LOG_INF("Role: %s", info.role == BT_CONN_ROLE_CENTRAL ? "Central" : "Peripheral");
+                CONFIG_BT_MAX_CONN);
+    } else {
+        LOG_INF("Connected (%u/%u)", (unsigned int)peer_count(), CONFIG_BT_MAX_CONN);
     }
-    else
+
-    {
+    if (peer_count() < CONFIG_BT_MAX_CONN) {
-        LOG_INF("Connected (info retrieval failed)");
+        (void)start_advertising();
     }
+
+    event_mgmt_set_event(EVENT_MGMT_BLE_CONNECTED);
 }
 
 static void disconnected(struct bt_conn *conn, uint8_t reason)
 {
-    LOG_INF("Disconnected (reason 0x%02x)", reason);
+    release_peer(conn);
+    advertising_active = false;
 
-    /* Startet Advertising mit dem global definierten Setup neu */
+    LOG_INF("Disconnected (reason 0x%02x, %u/%u active)", reason,
-    int rc = bt_le_adv_start(&adv_param, ad, ARRAY_SIZE(ad), sd, ARRAY_SIZE(sd));
+            (unsigned int)peer_count(), CONFIG_BT_MAX_CONN);
-    if (rc)
+
-    {
+    if (peer_count() < CONFIG_BT_MAX_CONN) {
-        LOG_ERR("Advertising failed to restart (err %d)", rc);
+        (void)start_advertising();
-    }
-    else
-    {
-        LOG_INF("Advertising successfully restarted");
-    }
     }
 
-static void le_phy_updated(struct bt_conn *conn, struct bt_conn_le_phy_info *param)
+    event_mgmt_set_event(EVENT_MGMT_BLE_DISCONNECTED);
-{
-    const char *tx_phy_str = (param->tx_phy == BT_GAP_LE_PHY_2M) ? "2M" : (param->tx_phy == BT_GAP_LE_PHY_1M) ? "1M" : "Coded/Unknown";
-    const char *rx_phy_str = (param->rx_phy == BT_GAP_LE_PHY_2M) ? "2M" : (param->rx_phy == BT_GAP_LE_PHY_1M) ? "1M" : "Coded/Unknown";
-
-    LOG_INF("LE PHY updated: TX PHY %s, RX PHY %s", tx_phy_str, rx_phy_str);
-}
-
-static void le_param_updated(struct bt_conn *conn, uint16_t interval,
-                             uint16_t latency, uint16_t timeout)
-{
-    LOG_INF("Connection parameters updated: Interval: %u, Latency: %u, Timeout: %u",
-            interval, latency, timeout);
 }
 
 BT_CONN_CB_DEFINE(conn_callbacks) = {
     .connected = connected,
     .disconnected = disconnected,
-    .le_param_updated = le_param_updated,
-    .le_phy_updated = le_phy_updated,
 };
 
+uint16_t ble_mgmt_get_max_payload(void)
+{
+    uint16_t mtu = current_att_mtu;
+
+#ifdef CONFIG_BT_L2CAP_TX_MTU
+    if (mtu > CONFIG_BT_L2CAP_TX_MTU) {
+        mtu = CONFIG_BT_L2CAP_TX_MTU;
+    }
+#endif
+
+    return (mtu > GATT_NOTIFY_OVERHEAD) ? (mtu - GATT_NOTIFY_OVERHEAD) : 20U;
+}
+
+int ble_mgmt_send(const uint8_t *data, uint16_t len)
+{
+    bool any_subscriber = false;
+    bool any_link_present = false;
+    int last_error = 0;
+
+    ARG_UNUSED(data);
+    ARG_UNUSED(len);
+
+    for (size_t index = 0; index < ARRAY_SIZE(peers); ++index) {
+        int rc;
+
+        if (peers[index].conn == NULL) {
+            continue;
+        }
+
+        any_link_present = true;
+
+        if (!bt_gatt_is_subscribed(peers[index].conn, &ble_mgmt_svc.attrs[4],
+                                   BT_GATT_CCC_NOTIFY)) {
+            continue;
+        }
+
+        any_subscriber = true;
+
+        do {
+            rc = bt_gatt_notify(peers[index].conn, &ble_mgmt_svc.attrs[4], data, len);
+            if (rc == -ENOMEM) {
+                k_sleep(K_MSEC(5));
+            }
+        } while (rc == -ENOMEM);
+
+        if (rc != 0) {
+            LOG_ERR("Failed to send notification (err %d)", rc);
+            last_error = rc;
+        }
+    }
+
+    if (!any_link_present || current_att_mtu <= DEFAULT_ATT_MTU) {
+        LOG_DBG("TX deferred: ATT not ready (links=%u, mtu=%u)",
+                (unsigned int)peer_count(), current_att_mtu);
+        return -EAGAIN;
+    }
+
+    if (!any_subscriber) {
+        LOG_DBG("TX blocked: no peer subscribed for notifications");
+        return -EACCES;
+    }
+
+    return last_error;
+}
+
+int ble_mgmt_update_adv_name(const char *new_name)
+{
+    set_device_name(new_name);
+
+    if (peer_count() >= CONFIG_BT_MAX_CONN && !advertising_active) {
+        return 0;
+    }
+
+    return restart_advertising();
+}
+
 int ble_mgmt_init(ble_mgmt_rx_cb_t rx_cb, const char *device_name)
 {
     int rc;
-    app_rx_cb = rx_cb;
-
     static struct bt_gatt_cb gatt_callbacks = {
         .att_mtu_updated = att_mtu_updated,
     };
 
-    bt_gatt_cb_register(&gatt_callbacks);
+    LOG_INF("ble_mgmt_init: starting");
+    app_rx_cb = rx_cb;
+    current_att_mtu = DEFAULT_ATT_MTU;
 
+    LOG_INF("ble_mgmt_init: calling bt_enable");
     rc = bt_enable(NULL);
-    if (rc)
+    if (rc != 0) {
-    {
         LOG_ERR("Bluetooth init failed (err %d)", rc);
         return rc;
     }
 
-    const char *name_to_use = (device_name != NULL) ? device_name : CONFIG_BLE_MGMT_DEFAULT_DEVICE_NAME;
+    LOG_INF("ble_mgmt_init: bt_enable done, marking ready");
-    LOG_INF("BLE init: set_device_name");
+    ble_ready = true;
-    set_device_name(name_to_use);
+    bt_gatt_cb_register(&gatt_callbacks);
+    advertising_active = false;
+    set_device_name(device_name);
 
-    LOG_INF("BLE init: bt_le_adv_start");
+    LOG_INF("ble_mgmt_init: calling start_advertising");
-    rc = bt_le_adv_start(&adv_param, ad, ARRAY_SIZE(ad), sd, ARRAY_SIZE(sd));
+    rc = start_advertising();
-    if (rc)
+    if (rc != 0) {
-    {
+        LOG_ERR("start_advertising failed (err %d)", rc);
-        LOG_ERR("Advertising failed to start (err %d)", rc);
         return rc;
     }
 
-    LOG_INF("Bluetooth initialized. Adv-Name: %s", current_device_name);
+    LOG_INF("ble_mgmt_init: complete");
     return 0;
 }

firmware/libs/buzz_proto/include/buzz_proto.h

@@ -36,6 +36,7 @@ enum buzz_data_type
     BUZZ_DATA_DEVICE_INFO = 0x02,
     BUZZ_DATA_FS_INFO = 0x03,
     BUZZ_DATA_FW_INFO = 0x04,
+    BUZZ_DATA_BATT_INFO = 0x05,
 
     BUZZ_DATA_FILE_GET = 0x20,
     BUZZ_DATA_FILE_PUT = 0x21,
@@ -122,6 +123,17 @@ struct __attribute__((packed)) buzz_resp_fw_info
     uint8_t kernel_version_length; /* Länge der Kernel-Versionszeichenkette */
     char data[];                   /* Variabler String ohne Null-Terminierung: [fw_version][kernel_version] */
 };
+
+/* Payload für die Batterie-Infos */
+struct __attribute__((packed)) buzz_resp_batt_info
+{
+    uint8_t data_type;      /* BUZZ_DATA_BATT_INFO */
+    uint8_t batt_status;    /* batt_mgmt_state_t */
+    uint8_t batt_level;     /* 0..4 */
+    uint8_t batt_percent;   /* 0..100 */
+    uint16_t batt_voltage_mv; /* Little Endian */
+};
+
 /* Payload für das Entfernen einer Datei */
 struct __attribute__((packed)) buzz_rm_file_payload
 {

firmware/libs/buzz_proto/src/buzz_proto.c

@@ -7,6 +7,7 @@
 #include <stdlib.h>
 
 #include "buzz_proto.h"
+#include "batt_mgmt.h"
 #include "fs_mgmt.h"
 #include "fw_mgmt.h"
 
@@ -293,6 +294,43 @@ static void handle_fw_info_request(struct buzz_frame_msg *msg)
     }
 }
 
+static void handle_batt_info_request(struct buzz_frame_msg *msg)
+{
+    struct buzz_proto_header *hdr = (struct buzz_proto_header *)msg->data_ptr;
+    struct buzz_resp_batt_info *resp_data = (struct buzz_resp_batt_info *)(msg->data_ptr + sizeof(*hdr));
+    batt_mgmt_info_t batt_info;
+    uint16_t voltage_mv = 0;
+    int rc = batt_mgmt_get_info(&batt_info);
+
+    if (rc < 0)
+    {
+        LOG_WRN("Failed to get battery info: %d", rc);
+        send_error_frame(msg, abs(rc));
+        return;
+    }
+
+    if (batt_info.voltage_mv > 0)
+    {
+        voltage_mv = (batt_info.voltage_mv > UINT16_MAX) ? UINT16_MAX : (uint16_t)batt_info.voltage_mv;
+    }
+
+    hdr->frame_type = BUZZ_FRAME_RESPONSE;
+    hdr->payload_length = sys_cpu_to_le16(sizeof(struct buzz_resp_batt_info));
+
+    resp_data->data_type = BUZZ_DATA_BATT_INFO;
+    resp_data->batt_status = (uint8_t)batt_info.state;
+    resp_data->batt_level = batt_info.level;
+    resp_data->batt_percent = batt_info.percent;
+    resp_data->batt_voltage_mv = sys_cpu_to_le16(voltage_mv);
+
+    if (msg->reply_cb)
+    {
+        msg->reply_cb(msg->data_ptr, sizeof(struct buzz_proto_header) + sizeof(struct buzz_resp_batt_info));
+    }
+    LOG_DBG("Battery Info sent: state=%u, level=%u, percent=%u, voltage=%u mV",
+            batt_info.state, batt_info.level, batt_info.percent, batt_info.voltage_mv);
+}
+
 static void handle_ls_request(struct buzz_frame_msg *msg)
 {
     struct buzz_proto_header *hdr = (struct buzz_proto_header *)msg->data_ptr;
@@ -698,6 +736,11 @@ static void handle_request(struct buzz_frame_msg *msg)
         handle_fw_info_request(msg);
         break;
 
+    case BUZZ_DATA_BATT_INFO:
+        LOG_DBG("Received BATT Info Request");
+        handle_batt_info_request(msg);
+        break;
+
     case BUZZ_DATA_FILE_GET:
         LOG_DBG("Received FILE_GET Request");
         handle_file_get_request(msg, false);

firmware/libs/event_mgmt/include/event_mgmt.h

@@ -7,6 +7,8 @@
 #define EVENT_MGMT_AUDIO_READY BIT(1)
 #define EVENT_MGMT_BLE_CONNECTED BIT(2)
 #define EVENT_MGMT_BLE_DISCONNECTED BIT(3)
+#define EVENT_MGMT_AUDIO_ACTIVE BIT(4)
+#define EVENT_MGMT_AUDIO_IDLE BIT(5)
 
 extern struct k_event event_mgmt_events;
 

firmware/libs/fs_mgmt/Kconfig

@@ -7,7 +7,7 @@ menuconfig FS_MGMT
     select FILE_SYSTEM_LITTLEFS
     select FILE_SYSTEM_MKFS
     select FLASH_PAGE_LAYOUT
-    select SPI_NOR if BOARD_BUZZY
+    select NORDIC_QSPI_NOR if BOARD_BUZZY
     select PM_OVERRIDE_EXTERNAL_DRIVER_CHECK if BOARD_BUZZY
     select NORDIC_QSPI_NOR if BOARD_NRF52840DK_NRF52840
     help

firmware/libs/fs_mgmt/src/fs_mgmt.c

@@ -12,13 +12,16 @@
 
 LOG_MODULE_REGISTER(fs_mgmt, CONFIG_FS_MGMT_LOG_LEVEL);
 
-/* Prefer external LittleFS partition when present, otherwise internal storage partition. */
+/*
-#if DT_NODE_EXISTS(DT_NODELABEL(ext_flash_lfs))
+ * Under sysbuild, Partition Manager generates PM_<name>_ID symbols.
+ * Without PM, we fall back to the DTS node label.
+ */
+#if defined(PM_littlefs_storage_ID)
+#define FS_PARTITION_ID PM_littlefs_storage_ID
+#elif DT_NODE_EXISTS(DT_NODELABEL(ext_flash_lfs))
 #define FS_PARTITION_ID FIXED_PARTITION_ID(ext_flash_lfs)
-#elif DT_NODE_EXISTS(DT_NODELABEL(storage_partition))
-#define FS_PARTITION_ID FIXED_PARTITION_ID(storage_partition)
 #else
-#error "No compatible LittleFS partition node label found (expected ext_flash_lfs or storage_partition)"
+#error "No compatible LittleFS partition found (expected PM littlefs_storage or DTS ext_flash_lfs)"
 #endif
 FS_LITTLEFS_DECLARE_DEFAULT_CONFIG(fs_storage_data);
 
@@ -35,8 +38,10 @@ static struct fs_mount_t fs_storage_mnt = {
     .mnt_point = CONFIG_FS_MGMT_MOUNT_POINT,
 };
 
+#if defined(CONFIG_PM_DEVICE) && !defined(CONFIG_FILE_SYSTEM_SHELL)
 static int open_count = 0;
 static struct k_mutex flash_pm_lock;
+#endif
 
 // #define ACK_WATERMARK (CONFIG_BUZZ_PROTO_SLAB_COUNT / 4)
 #define INITIAL_CREDITS CONFIG_BUZZ_PROTO_SLAB_COUNT
@@ -76,7 +81,9 @@ static struct
  */
 static int fs_mgmt_pm_flash_suspend(void)
 {
-#if IS_ENABLED(CONFIG_PM_DEVICE)
+#if defined(CONFIG_FILE_SYSTEM_SHELL)
+    return 0;
+#elif defined(CONFIG_PM_DEVICE)
     if (!device_is_ready(flash_dev))
     {
         return -ENODEV;
@@ -102,7 +109,7 @@ static int fs_mgmt_pm_flash_suspend(void)
     }
 
     k_mutex_unlock(&flash_pm_lock);
-#endif /* CONFIG_PM_DEVICE */
+#endif /* CONFIG_FILE_SYSTEM_SHELL / CONFIG_PM_DEVICE */
     return 0;
 }
 
@@ -113,7 +120,9 @@ static int fs_mgmt_pm_flash_suspend(void)
  */
 static int fs_mgmt_pm_flash_resume(void)
 {
-#if IS_ENABLED(CONFIG_PM_DEVICE)
+#if defined(CONFIG_FILE_SYSTEM_SHELL)
+    return 0;
+#elif defined(CONFIG_PM_DEVICE)
     if (!device_is_ready(flash_dev))
         return -ENODEV;
 
@@ -131,7 +140,7 @@ static int fs_mgmt_pm_flash_resume(void)
     open_count++;
 
     k_mutex_unlock(&flash_pm_lock);
-#endif /* CONFIG_PM_DEVICE */
+#endif /* CONFIG_FILE_SYSTEM_SHELL / CONFIG_PM_DEVICE */
     return 0;
 }
 
@@ -179,6 +188,20 @@ int fs_mgmt_pm_unlink(const char *path)
 {
     LOG_DBG("PM Unlinking file '%s'", path);
     fs_mgmt_pm_flash_resume();
+
+    struct fs_dirent entry;
+    int stat_rc = fs_stat(path, &entry);
+    if (stat_rc == -ENOENT)
+    {
+        fs_mgmt_pm_flash_suspend();
+        return 0;
+    }
+    if (stat_rc < 0)
+    {
+        fs_mgmt_pm_flash_suspend();
+        return stat_rc;
+    }
+
     int rc = fs_unlink(path);
     fs_mgmt_pm_flash_suspend();
     return rc;
@@ -397,7 +420,9 @@ int fs_mgmt_pm_mkdir_recursive(char *path)
 
 static int fs_mgmt_init(void)
 {
+#if defined(CONFIG_PM_DEVICE) && !defined(CONFIG_FILE_SYSTEM_SHELL)
     k_mutex_init(&flash_pm_lock);
+#endif
 
     if (!device_is_ready(flash_dev))
     {

firmware/libs/settings_mgmt/CMakeLists.txt

@@ -0,0 +1,5 @@
+if(CONFIG_SETTINGS_MGMT)
+  zephyr_library()
+  zephyr_library_sources(src/settings_mgmt.c)
+  zephyr_include_directories(include)
+endif()

firmware/libs/settings_mgmt/Kconfig

@@ -0,0 +1,15 @@
+menuconfig SETTINGS_MGMT
+    bool "Settings Management"
+    default y
+    select SETTINGS
+    select SETTINGS_RUNTIME
+    select ZMS
+    help
+      Library for initializing and managing the settings subsystem.
+      ZMS (Zephyr Memory Storage) backend is automatically selected when ZMS is enabled.
+
+if SETTINGS_MGMT
+    module = SETTINGS_MGMT
+    module-str = settings_mgmt
+    source "subsys/logging/Kconfig.template.log_config"
+endif # SETTINGS_MGMT

firmware/libs/settings_mgmt/include/settings_mgmt.h

@@ -0,0 +1,34 @@
+#ifndef SETTINGS_MGMT_H
+#define SETTINGS_MGMT_H
+
+#include <zephyr/types.h>
+
+struct app_settings_t {
+    /* System */
+    char dev_name[33];
+    
+    /* Audio */
+    uint8_t vol;
+    uint8_t shuffle_mode; /* 0: Rnd, 1: No-Rep */
+
+    /* BLE */
+    uint32_t ble_timeout;  /* Seconds, 0xFFFFFFFF = forever */
+    uint16_t ble_interval; /* Milliseconds */
+
+    /* Power & Calibration */
+    uint8_t chg_mode;      /* 0: 500mA, 1: 1A, 2: Auto */
+    uint16_t off_threshold;/* mV */
+    int16_t adc_gain;
+    int16_t adc_offset;
+};
+
+/* Global access to the current runtime configuration */
+extern struct app_settings_t app_cfg;
+
+/* Initializes the settings subsystem and loads values from flash */
+int settings_mgmt_init(void);
+
+/* Sets a setting via string path (for your protocol) */
+int settings_mgmt_set_by_path(const char *path, const void *value, size_t len);
+
+#endif

firmware/libs/settings_mgmt/src/settings_mgmt.c

@@ -0,0 +1,243 @@
+#include <zephyr/settings/settings.h>
+#include <zephyr/logging/log.h>
+#include <errno.h>
+#include <stdio.h>
+#include <string.h>
+#include "settings_mgmt.h"
+
+LOG_MODULE_REGISTER(settings_mgmt, LOG_LEVEL_INF);
+
+/* Sanity check limits */
+#define VOL_MIN                 0
+#define VOL_MAX                 100
+#define SHUFFLE_MODE_MIN        0
+#define SHUFFLE_MODE_MAX        1
+#define BLE_TIMEOUT_MIN         1000
+#define BLE_TIMEOUT_MAX         0xFFFFFFFF
+#define BLE_INTERVAL_MIN        10
+#define BLE_INTERVAL_MAX        10000
+#define CHG_MODE_MIN            0
+#define CHG_MODE_MAX            2
+#define OFF_THRESHOLD_MIN       2900  /* mV, LiPo cut-off */
+#define OFF_THRESHOLD_MAX       3500  /* mV, LiPo nominal */
+#define ADC_GAIN_MIN            -100
+#define ADC_GAIN_MAX            100
+#define ADC_OFFSET_MIN          -1000
+#define ADC_OFFSET_MAX          1000
+
+/* The "Source of Truth" in RAM */
+struct app_settings_t app_cfg = {
+#ifdef CONFIG_BLE_MGMT_DEFAULT_DEVICE_NAME
+    .dev_name = CONFIG_BLE_MGMT_DEFAULT_DEVICE_NAME,
+#else
+    .dev_name = CONFIG_BOARD, /* Default to board name if no explicit default set */
+#endif
+    .vol = 100,               /* 0-100 % */
+    .shuffle_mode = 0,
+    .ble_timeout = 0xFFFFFFFF,
+    .ble_interval = 100,
+    .chg_mode = 2,            /* Auto */
+    .off_threshold = 3000,    /* mV */
+    .adc_gain = 0,
+    .adc_offset = 0,
+};
+
+static int read_exact(settings_read_cb read_cb, void *cb_arg,
+                      void *dst, size_t expected_len)
+{
+    int rc = read_cb(cb_arg, dst, expected_len);
+
+    if (rc < 0) {
+        return rc;
+    }
+
+    if ((size_t)rc != expected_len) {
+        return -EINVAL;
+    }
+
+    return 0;
+}
+
+/* Sanity check helpers */
+static int check_uint8_range(uint8_t val, uint8_t min, uint8_t max,
+                              const char *name)
+{
+    if (val < min || val > max) {
+        LOG_WRN("%s out of range: %u (valid: %u-%u)", name, val, min, max);
+        return -EINVAL;
+    }
+    return 0;
+}
+
+static int check_uint16_range(uint16_t val, uint16_t min, uint16_t max,
+                               const char *name)
+{
+    if (val < min || val > max) {
+        LOG_WRN("%s out of range: %u (valid: %u-%u)", name, val, min, max);
+        return -EINVAL;
+    }
+    return 0;
+}
+
+static int check_uint32_range(uint32_t val, uint32_t min, uint32_t max,
+                               const char *name)
+{
+    if (val < min || val > max) {
+        LOG_WRN("%s out of range: %u (valid: %u-%u)", name, val, min, max);
+        return -EINVAL;
+    }
+    return 0;
+}
+
+static int check_int16_range(int16_t val, int16_t min, int16_t max,
+                              const char *name)
+{
+    if (val < min || val > max) {
+        LOG_WRN("%s out of range: %d (valid: %d-%d)", name, val, min, max);
+        return -EINVAL;
+    }
+    return 0;
+}
+
+/* Callback: Called by settings_load() or settings_runtime_set() */
+static int buzzy_settings_set(const char *name, size_t len,
+                             settings_read_cb read_cb, void *cb_arg)
+{
+    const char *next;
+    int rc;
+
+    /* Path matching: "buzzy/sys/name" -> name is "sys/name" here */
+    if (settings_name_steq(name, "sys/name", &next) && !next) {
+        rc = read_cb(cb_arg, app_cfg.dev_name, sizeof(app_cfg.dev_name) - 1);
+        if (rc >= 0) app_cfg.dev_name[rc] = '\0';
+        return 0;
+    }
+
+    if (settings_name_steq(name, "audio/vol", &next) && !next) {
+        uint8_t vol;
+        rc = read_exact(read_cb, cb_arg, &vol, sizeof(vol));
+        if (rc == 0) {
+            rc = check_uint8_range(vol, VOL_MIN, VOL_MAX, "audio/vol");
+            if (rc == 0) {
+                app_cfg.vol = vol;
+            }
+        }
+        return rc;
+    }
+
+    if ((settings_name_steq(name, "audio/shuffle", &next) ||
+         settings_name_steq(name, "audio/shuffle_mode", &next)) && !next) {
+        uint8_t shuffle;
+        rc = read_exact(read_cb, cb_arg, &shuffle, sizeof(shuffle));
+        if (rc == 0) {
+            rc = check_uint8_range(shuffle, SHUFFLE_MODE_MIN, SHUFFLE_MODE_MAX, "shuffle_mode");
+            if (rc == 0) {
+                app_cfg.shuffle_mode = shuffle;
+            }
+        }
+        return rc;
+    }
+
+    if (settings_name_steq(name, "ble/to", &next) && !next) {
+        uint32_t timeout;
+        rc = read_exact(read_cb, cb_arg, &timeout, sizeof(timeout));
+        if (rc == 0) {
+            rc = check_uint32_range(timeout, BLE_TIMEOUT_MIN, BLE_TIMEOUT_MAX, "ble/to");
+            if (rc == 0) {
+                app_cfg.ble_timeout = timeout;
+            }
+        }
+        return rc;
+    }
+
+    if ((settings_name_steq(name, "ble/interval", &next) ||
+         settings_name_steq(name, "ble/int", &next)) && !next) {
+        uint16_t interval;
+        rc = read_exact(read_cb, cb_arg, &interval, sizeof(interval));
+        if (rc == 0) {
+            rc = check_uint16_range(interval, BLE_INTERVAL_MIN, BLE_INTERVAL_MAX, "ble/interval");
+            if (rc == 0) {
+                app_cfg.ble_interval = interval;
+            }
+        }
+        return rc;
+    }
+
+    if ((settings_name_steq(name, "power/chg_mode", &next) ||
+         settings_name_steq(name, "sys/chg_mode", &next)) && !next) {
+        uint8_t chg_mode;
+        rc = read_exact(read_cb, cb_arg, &chg_mode, sizeof(chg_mode));
+        if (rc == 0) {
+            rc = check_uint8_range(chg_mode, CHG_MODE_MIN, CHG_MODE_MAX, "chg_mode");
+            if (rc == 0) {
+                app_cfg.chg_mode = chg_mode;
+            }
+        }
+        return rc;
+    }
+
+    if ((settings_name_steq(name, "power/off_threshold", &next) ||
+         settings_name_steq(name, "sys/off_threshold", &next)) && !next) {
+        uint16_t threshold;
+        rc = read_exact(read_cb, cb_arg, &threshold, sizeof(threshold));
+        if (rc == 0) {
+            rc = check_uint16_range(threshold, OFF_THRESHOLD_MIN, OFF_THRESHOLD_MAX, "off_threshold [mV]");
+            if (rc == 0) {
+                app_cfg.off_threshold = threshold;
+            }
+        }
+        return rc;
+    }
+
+    if (settings_name_steq(name, "adc/gain", &next) && !next) {
+        int16_t gain;
+        rc = read_exact(read_cb, cb_arg, &gain, sizeof(gain));
+        if (rc == 0) {
+            rc = check_int16_range(gain, ADC_GAIN_MIN, ADC_GAIN_MAX, "adc/gain");
+            if (rc == 0) {
+                app_cfg.adc_gain = gain;
+            }
+        }
+        return rc;
+    }
+
+    if (settings_name_steq(name, "adc/offset", &next) && !next) {
+        int16_t offset;
+        rc = read_exact(read_cb, cb_arg, &offset, sizeof(offset));
+        if (rc == 0) {
+            rc = check_int16_range(offset, ADC_OFFSET_MIN, ADC_OFFSET_MAX, "adc/offset");
+            if (rc == 0) {
+                app_cfg.adc_offset = offset;
+            }
+        }
+        return rc;
+    }
+
+    return -ENOENT;
+}
+
+struct settings_handler buzzy_handler = {
+    .name = "buzzy",
+    .h_set = buzzy_settings_set
+};
+
+int settings_mgmt_set_by_path(const char *path, const void *value, size_t len)
+{
+    char full_path[64];
+    snprintf(full_path, sizeof(full_path), "buzzy/%s", path);
+    
+    /* Schreibt in ZMS UND triggert buzzy_settings_set zur RAM-Aktualisierung */
+    return settings_runtime_set(full_path, value, len);
+}
+
+int settings_mgmt_init(void)
+{
+    int rc = settings_subsys_init();
+    if (rc) return rc;
+
+    rc = settings_register(&buzzy_handler);
+    if (rc) return rc;
+
+    /* Lädt alle gespeicherten Werte aus dem ZMS in die app_cfg Struktur */
+    return settings_load();
+}

firmware/libs/usb_mgmt/CMakeLists.txt

@@ -0,0 +1,5 @@
+if(CONFIG_USB_MGMT)
+  zephyr_library()
+  zephyr_library_sources(src/usb_mgmt.c)
+  zephyr_include_directories(include)
+endif()

firmware/libs/usb_mgmt/Kconfig

@@ -0,0 +1,13 @@
+menuconfig USB_MGMT
+    bool "USB Management"
+    default y
+    select NRFX_POWER
+    help
+      Library for USB-related queries, e.g. VBUS presence detection
+      via the nRF52840 POWER peripheral.
+
+if USB_MGMT
+    module = USB_MGMT
+    module-str = usb_mgmt
+    source "subsys/logging/Kconfig.template.log_config"
+endif # USB_MGMT

firmware/libs/usb_mgmt/include/usb_mgmt.h

@@ -0,0 +1,30 @@
+#ifndef USB_MGMT_H
+#define USB_MGMT_H
+
+#include <stdbool.h>
+#include <zephyr/kernel.h>
+
+#define USB_MGMT_VBUS_CONNECTED BIT(0)
+#define USB_MGMT_VBUS_DISCONNECTED BIT(1)
+
+extern struct k_event usb_mgmt_events;
+
+/**
+ * @brief Wait until usb_mgmt has completed initialization.
+ *
+ * @param timeout Timeout for waiting.
+ *
+ * @retval true usb_mgmt is ready.
+ * @retval false timeout occurred.
+ */
+bool usb_mgmt_wait_ready(k_timeout_t timeout);
+
+/**
+ * @brief Returns true when VBUS (USB 5 V) is present.
+ *
+ * Reads the USBREGSTATUS.VBUSDETECT bit in the nRF52840 POWER peripheral.
+ * No USB stack needs to be enabled.
+ */
+bool usb_mgmt_is_vbus_present(void);
+
+#endif /* USB_MGMT_H */

firmware/libs/usb_mgmt/src/usb_mgmt.c

@@ -0,0 +1,65 @@
+#include <hal/nrf_power.h>
+#include <nrfx_power.h>
+#include <errno.h>
+#include <zephyr/logging/log.h>
+
+#include "usb_mgmt.h"
+
+LOG_MODULE_REGISTER(usb_mgmt, CONFIG_USB_MGMT_LOG_LEVEL);
+
+K_EVENT_DEFINE(usb_mgmt_events);
+K_SEM_DEFINE(usb_mgmt_ready_sem, 0, 1);
+
+static bool usb_mgmt_last_vbus_state;
+static bool usb_mgmt_ready;
+
+static void usb_mgmt_power_handler(nrfx_power_usb_evt_t event)
+{
+	bool is_present = (event == NRFX_POWER_USB_EVT_DETECTED);
+
+	LOG_INF("VBUS %s (event=%u)", is_present ? "connected" : "disconnected", event);
+
+	if (is_present != usb_mgmt_last_vbus_state) {
+		usb_mgmt_last_vbus_state = is_present;
+		k_event_post(&usb_mgmt_events,
+			     is_present ? USB_MGMT_VBUS_CONNECTED : USB_MGMT_VBUS_DISCONNECTED);
+	}
+}
+
+static int usb_mgmt_init(void)
+{
+	usb_mgmt_last_vbus_state = nrf_power_usbregstatus_vbusdet_get(NRF_POWER);
+	LOG_DBG("Boot VBUS state: %s", usb_mgmt_last_vbus_state ? "present" : "absent");
+	k_event_post(&usb_mgmt_events,
+		     usb_mgmt_last_vbus_state ? USB_MGMT_VBUS_CONNECTED : USB_MGMT_VBUS_DISCONNECTED);
+
+	nrfx_power_config_t config = { 0 };
+	nrfx_power_usbevt_config_t usb_config = {
+		.handler = usb_mgmt_power_handler,
+	};
+
+	nrfx_power_init(&config);
+	nrfx_power_usbevt_init(&usb_config);
+	nrfx_power_usbevt_enable();
+
+	usb_mgmt_ready = true;
+	k_sem_give(&usb_mgmt_ready_sem);
+
+	return 0;
+}
+
+SYS_INIT(usb_mgmt_init, APPLICATION, CONFIG_APPLICATION_INIT_PRIORITY);
+
+bool usb_mgmt_is_vbus_present(void)
+{
+	return usb_mgmt_last_vbus_state;
+}
+
+bool usb_mgmt_wait_ready(k_timeout_t timeout)
+{
+	if (usb_mgmt_ready) {
+		return true;
+	}
+
+	return k_sem_take(&usb_mgmt_ready_sem, timeout) == 0;
+}

firmware/output.txt

@@ -0,0 +1,2 @@
+ERROR: Build directory /Users/edi/nrf_playground/buzzer_2/firmware/build targets board buzzy/nrf52840, but board {self.args.board} was specified. (Clean the directory, use --pristine, or use --build-dir to specify a different one.)
+FATAL ERROR: refusing to proceed without --force due to above error

firmware/pm_static.yml

@@ -1,4 +1,39 @@
-# External Flash
+# Static Partition Manager layout for sysbuild builds.
+# Keep this aligned with boards/iten/buzzy/buzzy.dts internal flash partitions.
+
+mcuboot:
+  address: 0x0
+  size: 0xC000
+  region: flash_primary
+
+mcuboot_pad:
+  address: 0xC000
+  size: 0x200
+  region: flash_primary
+
+app:
+  address: 0xC200
+  size: 0x75E00
+  region: flash_primary
+
+mcuboot_primary:
+  address: 0xC000
+  size: 0x76000
+  region: flash_primary
+  span: [mcuboot_pad, app]
+
+mcuboot_secondary:
+  address: 0x82000
+  size: 0x76000
+  region: flash_primary
+
+# Internal flash tail partition (8 x 4 KiB pages) for ZMS/settings-style usage.
+storage:
+  address: 0xF8000
+  size: 0x8000
+  region: flash_primary
+
+# External flash LittleFS image area.
 littlefs_storage:
   address: 0x0
   size: 0x800000

firmware/pm_static_nrf52840dk_nrf52840.yml

@@ -1,39 +0,0 @@
-# mcuboot:
-#   address: 0x0
-#   size: 0xC000
-#   region: flash_primary
-
-# # Primary Slot: Start bleibt 0xC000, Größe 200KB (0x32000)
-# mcuboot_primary:
-#   address: 0xC000
-#   size: 0x32000
-#   region: flash_primary
-
-# mcuboot_pad:
-#   address: 0xC000
-#   size: 0x200
-#   region: flash_primary
-
-# # Die App startet nach dem Padding des Primary Slots
-# app:
-#   address: 0xC200
-#   size: 0x31E00  # (0x32000 - 0x200)
-#   region: flash_primary
-
-# # Secondary Slot: Startet jetzt bei 0xC000 + 0x32000 = 0x3E000
-# mcuboot_secondary:
-#   address: 0x3E000
-#   size: 0x32000
-#   region: flash_primary
-
-# # NVS storage am Ende des Flashs, 16KB (0x4000)
-# settings_storage:
-#   address: 0xFC000
-#   size: 0x4000
-#   region: flash_primary
-
-# External Flash
-littlefs_storage:
-  address: 0x0
-  size: 0x800000  # 8MB
-  region: external_flash

firmware/prj.conf

@@ -1,6 +1,3 @@
-### Bluetooth
-CONFIG_BLE_MGMT=y
-
 ### Error handling
 CONFIG_HW_STACK_PROTECTION=y
 CONFIG_RESET_ON_FATAL_ERROR=y
@@ -8,5 +5,9 @@ CONFIG_RESET_ON_FATAL_ERROR=y
 ### Power management
 CONFIG_PM_DEVICE=y
 
+### Boot banner
+CONFIG_NCS_APPLICATION_BOOT_BANNER_STRING="Edis Buzzer"
+
 ### Stack
 CONFIG_MAIN_STACK_SIZE=2048
+CONFIG_BT_RX_STACK_SIZE=4096

firmware/rtt_script.jlink

@@ -0,0 +1,5 @@
+connect
+rtt start
+sleep 3000
+rtt stop
+exit

firmware/src/main.c

@@ -2,13 +2,30 @@
 #include <zephyr/logging/log.h>
 #include <string.h>
 
-#include "fs_mgmt.h"
 #include "buzz_proto.h"
-#include "fw_mgmt.h"
+#include "settings_mgmt.h"
+#include "batt_mgmt.h"
+// #include "fw_mgmt.h"
 // #include "audio.h"
 
 LOG_MODULE_REGISTER(main);
 
+static const char *battery_state_to_str(batt_mgmt_state_t state)
+{
+    switch (state) {
+    case BATT_STATE_DISCHARGING:
+        return "discharging";
+    case BATT_STATE_FULL:
+        return "full";
+    case BATT_STATE_CHARGING:
+        return "charging";
+    case BATT_STATE_ERROR:
+        return "error";
+    default:
+        return "unknown";
+    }
+}
+
 #if IS_ENABLED(CONFIG_BLE_MGMT)
 #include "ble_mgmt.h"
 void ble_rx_cb(const uint8_t *data, uint16_t len)
@@ -49,24 +66,36 @@ void ble_rx_cb(const uint8_t *data, uint16_t len)
 
 int main(void)
 {
+
 #if IS_ENABLED(CONFIG_BLE_MGMT)
     /* BLE-Subsystem initialisieren und RX-Callback registrieren */
-    int rc = ble_mgmt_init(ble_rx_cb, CONFIG_BLE_MGMT_DEFAULT_DEVICE_NAME);
+    int rc = ble_mgmt_init(ble_rx_cb, app_cfg.dev_name);
     if (rc < 0) {
         LOG_ERR("Failed to initialize BLE management: %d", rc);
         return rc;
     }
-    LOG_WRN("After BLE init");
 #else
     LOG_WRN("BLE not enabled");
 #endif
 
-    LOG_WRN("Main park loop active");
+#if IS_ENABLED(CONFIG_LOG)
+#if IS_ENABLED(CONFIG_BATT_MGMT)
+    k_sleep(K_SECONDS(1));
+    batt_mgmt_info_t batt_info;
+    int batt_rc = batt_mgmt_get_info(&batt_info);
+    if (batt_rc == 0) {
+        LOG_INF("Battery after 1s: %d mV, %u%%, level=%u, state=%s (%d)",
+                batt_info.voltage_mv,
+                batt_info.percent,
+                batt_info.level,
+                battery_state_to_str(batt_info.state),
+                batt_info.state);
+    } else {
+        LOG_WRN("Battery info read failed: %d", batt_rc);
+    }
+#endif // CONFIG_BATT_MGMT
+#endif // CONFIG_LOG
     
-    // k_sleep(K_MSEC(500));
-    // LOG_INF("Playing test audio files...");
-    // audio_queue_play("/lfs/sys/update", false);
-    // audio_queue_play("/lfs/sys/confirm", false);
     for (;;) {
         int32_t rem_ms = k_sleep(K_FOREVER);
         LOG_WRN("main woke unexpectedly (remaining=%d ms)", rem_ms);

protocol.md

@@ -92,6 +92,7 @@ Das Protokoll ist so ausgelegt, dass es mit mindestens 100 Bytes auskommen sollt
 | `0x02` | `DEVICE_INFO` | aktiv | Device-Infos (Board, Revision, SOC, ID) |
 | `0x03` | `FS_INFO` | aktiv | Dateisystem- und Pfadinfos |
 | `0x04` | `FW_INFO` | aktiv | Info über Firmware-Status und -Version sowie Kernelversion |
+| `0x05` | `BATT_INFO` | aktiv | Info über die Batterie |
 | `0x20` | `FILE_GET` | aktiv | Datei vom Device streamen |
 | `0x21` | `FILE_PUT` | aktiv | Datei zum Device hochladen |
 | `0x22` | `TAGS_GET` | aktiv | nur Tag-Bereich streamen |
@@ -238,6 +239,7 @@ Request: keine Zusatzdaten
 Response:
 
 ```c
+uint8_t data_type;           /* 0x04 */
 uint8_t fw_status;           /* 0x00: Confirmed, 0x01: Pending, 0x02: Testing, 0xFF: Unbekannt */
 uint32_t slot1_size;         /* (LE) Grösse des Firmware Update Slots */
 uint8_t fw_version_len;      /* Länge des Firmware-Versionsstring */
@@ -247,6 +249,20 @@ uint8_t data[];              /* FW-Version und Kernelversion, ohne Nullterminier
 
 ***Hinweis:*** in der Aktuellen implementierung werden die Versionen auf 32 Zeichen limitiert.
 
+### `BATT_INFO` (`0x05`)
+
+Request: keine Zusatzdaten
+
+Response:
+
+```c
+uint8_t data_type;           /* 0x05 */
+uint8_t batt_status;         /* 0x00: Discharging, 0x01: Full, 0x02: Charging, 0x03: Error, 0x04: Unknown */
+uint8_t batt_level;          /* 0-4, Anzahl Striche für den Akku */
+uint8_t batt_percent;        /* Akku-Füllstand in Prozent */
+uint16_t batt_voltage_mv;    /* (LE) Batteriespannung in mV */
+```
+
 ### `LS` (`0x40`)
 
 Request-Payload:

webpage/src/components/DeviceInfo.svelte

@@ -1,7 +1,7 @@
 <script lang="ts">
   import FlashUsage from "./FlashUsage.svelte";
-  import { deviceInfo, fwInfo } from "../lib/store";
+  import { battInfo, deviceInfo, fwInfo } from "../lib/store";
-  import { FW_STATUS } from "../lib/protocol/constants";
+  import { BATT_STATUS, FW_STATUS } from "../lib/protocol/constants";
   import { tooltip } from "../lib/actions/tooltip";
   import {
     CheckCircleIcon,
@@ -13,6 +13,52 @@
     BatteryFullIcon,
     BatteryChargingIcon,
   } from "phosphor-svelte";
+
+  function clampBatteryLevel(level: number): number {
+    if (Number.isNaN(level)) return 0;
+    return Math.max(0, Math.min(4, Math.trunc(level)));
+  }
+
+  $: resolvedBattIcon = (() => {
+    if (!$battInfo) return BatteryEmptyIcon;
+    if ($battInfo.battStatus === BATT_STATUS.CHARGING) return BatteryChargingIcon;
+
+    switch (clampBatteryLevel($battInfo.battLevel)) {
+      case 0:
+        return BatteryEmptyIcon;
+      case 1:
+        return BatteryLowIcon;
+      case 2:
+        return BatteryMediumIcon;
+      case 3:
+        return BatteryHighIcon;
+      default:
+        return BatteryFullIcon;
+    }
+  })();
+
+  $: battStatusText = (() => {
+    if (!$battInfo) return "unbekannt";
+    switch ($battInfo.battStatus) {
+      case BATT_STATUS.DISCHARGING:
+        return "Entladen";
+      case BATT_STATUS.FULL:
+        return "Voll";
+      case BATT_STATUS.CHARGING:
+        return "Laden";
+      case BATT_STATUS.ERROR:
+        return "Fehler";
+      default:
+        return "Unbekannt";
+    }
+  })();
+
+  $: battIconClass =
+    $battInfo?.battStatus === BATT_STATUS.ERROR
+      ? "w-5 h-5 text-red-500"
+      : $battInfo?.battStatus === BATT_STATUS.CHARGING
+        ? "w-5 h-5 text-emerald-600"
+        : "w-5 h-5";
 </script>
 
 <div class="text-sm">
@@ -127,7 +173,14 @@
       <tr>
         <td class="key">Batterie</td>
         <td class="value flex items-center gap-2">
-          85% <BatteryChargingIcon weight="bold" class="w-5 h-5" /> 1200mAh
+          {#if $battInfo}
+            <span>{$battInfo.battPercent}%</span>
+            <svelte:component this={resolvedBattIcon} weight="bold" class={battIconClass} />
+            <span class="text-text-muted">{$battInfo.battVoltageMv} mV</span>
+            <span class="text-text-muted">({battStatusText})</span>
+          {:else}
+            unbekannt
+          {/if}
         </td>
       </tr>
       <tr>

webpage/src/lib/protocol/constants.ts

@@ -27,6 +27,7 @@ export const DATA = {
     DEVICE_INFO: 0x02,
     FS_INFO: 0x03,
     FW_INFO: 0x04,
+    BATT_INFO: 0x05,
 
     FILE_GET: 0x20,
     FILE_PUT: 0x21,
@@ -66,3 +67,11 @@ export const FW_STATUS = {
     TESTING: 0x02,
     UNKNOWN: 0xFF,
 }
+
+export const BATT_STATUS = {
+    DISCHARGING: 0x00,
+    FULL: 0x01,
+    CHARGING: 0x02,
+    ERROR: 0x03,
+    UNKNOWN: 0x04,
+};

webpage/src/lib/protocol/parser.ts

@@ -1,5 +1,5 @@
 import { FRAME, DATA, ZEPHYR_ERRORS } from './constants';
-import { protocolInfo, deviceInfo, fsInfo, transferStats, fwInfo, resetTransferStats, transferDetails } from '../store';
+import { protocolInfo, deviceInfo, fsInfo, transferStats, fwInfo, battInfo, resetTransferStats, transferDetails } from '../store';
 import { addToast } from '../toast';
 import { SETTINGS } from '../settings';
 import { crc32 } from './crc32';
@@ -84,6 +84,18 @@ export function parseIncomingFrame(view: DataView, sender: FrameSender) {
                     const fwVersion = new TextDecoder().decode(new Uint8Array(view.buffer, 11, fw_version_length));
                     const kernelVersion = new TextDecoder().decode(new Uint8Array(view.buffer, 11 + fw_version_length, kernel_version_length));
                     fwInfo.set({ fwStatus, slot1Size, fwVersion, kernelVersion });
+                    break;
+                case DATA.BATT_INFO:
+                    if (payloadLength < 6) {
+                        console.warn(`Invalid BATT_INFO payload length: ${payloadLength}`);
+                        break;
+                    }
+                    const battStatus = view.getUint8(4);
+                    const battLevel = view.getUint8(5);
+                    const battPercent = view.getUint8(6);
+                    const battVoltageMv = view.getUint16(7, true);
+                    battInfo.set({ battStatus, battLevel, battPercent, battVoltageMv });
+                    break;
             }
             break;
 
@@ -287,7 +299,14 @@ export function parseIncomingFrame(view: DataView, sender: FrameSender) {
 
         case FRAME.ERROR:
             const errorCode = view.getUint16(3, true);
-            console.error(`Received error frame with code: 0x${errorCode.toString(16)}`);
+            const errorInfo = ZEPHYR_ERRORS[errorCode];
+            if (errorInfo) {
+                console.error(
+                    `Received error frame: 0x${errorCode.toString(16).padStart(2, '0')} (${errorInfo.zephyr}) - ${errorInfo.text}`
+                );
+            } else {
+                console.error(`Received error frame with code: 0x${errorCode.toString(16).padStart(2, '0')}`);
+            }
             showErrorToast(errorCode);
             if (lsReject) {
                 const currentReject = lsReject;
@@ -358,9 +377,21 @@ export function buildFWInfoRequest(): ArrayBuffer {
     return buffer;
 }
 
+export function buildBattInfoRequest(): ArrayBuffer {
+    const buffer = new ArrayBuffer(4);
+    const view = new DataView(buffer);
+
+    view.setUint8(0, FRAME.REQUEST);
+    view.setUint16(1, 1, true);
+    view.setUint8(3, DATA.BATT_INFO);
+
+    return buffer;
+}
+
 export function buildLSRequest(path: string): ArrayBuffer {
     const encoder = new TextEncoder();
     const pathBytes = encoder.encode(path);
+    console.debug(`[Protocol] LS request for path: ${path}`);
     const buffer = new ArrayBuffer(4 + pathBytes.length);
     const view = new DataView(buffer);
 
@@ -442,6 +473,7 @@ export function setFileGetResolver(
 export function buildFileGetRequest(path: string): ArrayBuffer {
     const encoder = new TextEncoder();
     const pathBytes = encoder.encode(path);
+    console.debug(`[Protocol] FILE_GET request for path: ${path}`);
     const buffer = new ArrayBuffer(4 + pathBytes.length);
     const view = new DataView(buffer);
 
@@ -458,6 +490,7 @@ export function buildFileGetRequest(path: string): ArrayBuffer {
 export function buildTagsGetRequest(path: string): ArrayBuffer {
     const encoder = new TextEncoder();
     const pathBytes = encoder.encode(path);
+    console.debug(`[Protocol] TAGS_GET request for path: ${path}`);
     const buffer = new ArrayBuffer(4 + pathBytes.length);
     const view = new DataView(buffer);
 

webpage/src/lib/settings.ts

@@ -7,6 +7,7 @@ export const SETTINGS = {
     bluetooth: {
         connectionTimeoutMs: 3000, // Timeout für den Verbindungsaufbau
         appleMaxInflight: 15, // iOS erlaubt nur wenige unbestätigte Nachrichten, daher begrenzen wir die Anzahl der gleichzeitig gesendeten Frames
+      batteryPollIntervalMs: 60_000, // Intervall für periodische BATT_INFO-Abfragen
     },
     ui: {
         toastDurationMs: 5000,

webpage/src/lib/store.ts

@@ -53,6 +53,13 @@ export interface FwInfo {
     kernelVersion: string;
 }
 
+export interface BattInfo {
+    battStatus: number;
+    battLevel: number;
+    battPercent: number;
+    battVoltageMv: number;
+}
+
 export interface StorageUsage {
     totalBytes: number;
     freeBytes: number;
@@ -84,6 +91,7 @@ export const protocolInfo = writable<ProtocolInfo | null>(null);
 export const deviceInfo = writable<DeviceInfo | null>(null);
 export const fsInfo = writable<FsInfo | null>(null);
 export const fwInfo = writable<FwInfo | null>(null);
+export const battInfo = writable<BattInfo | null>(null);
 
 // Dateilisten
 export const buzzerAudioFiles = writable<BuzzerFile[]>([]);
@@ -277,6 +285,7 @@ export function resetRemote(): void {
     deviceInfo.set(null);
     fsInfo.set(null);
     fwInfo.set(null);
+    battInfo.set(null);
     activeDeviceId.set(null);
     buzzerAudioFiles.set([]);
     buzzerSysFiles.set([]);

webpage/src/lib/sync.ts

@@ -1,6 +1,6 @@
 import { get } from 'svelte/store';
 import { isConnected, deviceInfo, fsInfo, fwInfo, buzzerAudioFiles, buzzerSysFiles, isTransferingRemote, isFetchingLocal, storageUsage, localAudioFiles, transferStats } from './store';
-import { requestProtocolInfo, requestFSInfo, fetchDirectory, getFile, putFile, deleteRemoteFile, requestDeviceInfo, requestFWInfo } from './transport';
+import { requestProtocolInfo, requestFSInfo, fetchDirectory, getFile, putFile, deleteRemoteFile, requestDeviceInfo, requestFWInfo, requestBattInfo } from './transport';
 import type { BuzzerFile } from './types';
 import { addToast } from './toast';
 import { getLocalFiles, deleteLocalFile, getLocalFile } from './db';
@@ -28,18 +28,25 @@ export async function refreshRemote() {
         await requestProtocolInfo();
         await requestFSInfo();
         await requestFWInfo();
+        await requestBattInfo();
         await requestDeviceInfo();
 
         // Kurze Verzögerung für Store-Propagation
         await new Promise(r => setTimeout(r, 100));
 
         const currentFsInfo = get(fsInfo);
+        console.debug("[Sync] Remote FS info:", currentFsInfo);
 
         // Sequenzielle Abfrage via Transport-Layer
-        const sysFiles = await fetchDirectory(currentFsInfo?.sysPath || "/lfs/sys");
+        const sysPath = currentFsInfo?.sysPath || "/lfs/sys";
+        const audioPath = currentFsInfo?.audioPath || "/lfs/a";
+
+        console.debug(`[Sync] Listing system directory: ${sysPath}`);
+        const sysFiles = await fetchDirectory(sysPath);
         buzzerSysFiles.set(sysFiles.map(mapToBuzzerFile));
 
-        const audioFiles = await fetchDirectory(currentFsInfo?.audioPath || "/lfs/a");
+        console.debug(`[Sync] Listing audio directory: ${audioPath}`);
+        const audioFiles = await fetchDirectory(audioPath);
         let mappedAudio = audioFiles.map(mapToBuzzerFile);
 
         // Dateien sofort im UI anzeigen, bevor die Tags geladen sind
@@ -101,6 +108,7 @@ export async function refreshLocal() {
 export async function downloadSelectedFiles() {
     const files = get(buzzerAudioFiles).filter(f => f.selected);
     const pathPrefix = get(fsInfo)?.audioPath || "/lfs/a";
+    console.debug(`[Sync] Download prefix: ${pathPrefix}`);
 
     if (files.length === 0) {
         addToast("Keine Dateien zum Herunterladen ausgewählt.", "warning");
@@ -181,6 +189,7 @@ export async function deleteSelectedLocalFiles() {
 export async function deleteSelectedRemoteFiles() {
     const files = get(buzzerAudioFiles).filter(f => f.selected);
     const pathPrefix = get(fsInfo)?.audioPath || "/lfs/a";
+    console.debug(`[Sync] Delete prefix: ${pathPrefix}`);
 
     if (files.length === 0) return;
 
@@ -208,6 +217,7 @@ export async function deleteSelectedRemoteFiles() {
 export async function uploadSelectedFiles() {
     const files = get(localAudioFiles).filter(f => f.selected);
     const pathPrefix = get(fsInfo)?.audioPath || "/lfs/a";
+    console.debug(`[Sync] Upload prefix: ${pathPrefix}`);
 
     if (files.length === 0) {
         addToast("Keine Dateien zum Hochladen ausgewählt.", "warning");

webpage/src/lib/transport.ts

@@ -1,4 +1,4 @@
-import { buildLSRequest, buildProtocolInfoRequest, buildDeviceInfoRequest, buildFSInfoRequest, buildFWInfoRequest, setLsResolver, buildFileGetRequest, setFileGetResolver, buildTagsGetRequest, uploadState } from './protocol/parser';
+import { buildLSRequest, buildProtocolInfoRequest, buildDeviceInfoRequest, buildFSInfoRequest, buildFWInfoRequest, buildBattInfoRequest, setLsResolver, buildFileGetRequest, setFileGetResolver, buildTagsGetRequest, uploadState } from './protocol/parser';
 import { crc32 } from './protocol/crc32';
 import { get } from 'svelte/store';
 import { protocolInfo, transferStats, } from './store';
@@ -10,9 +10,45 @@ const isMac = navigator.userAgent.includes('Macintosh') || navigator.userAgent.i
 const MAX_INFLIGHT = isMac ? SETTINGS.bluetooth.appleMaxInflight : Infinity;  // iOS erlaubt nur wenige unbestätigte Nachrichten
 
 console.log("Transport: Max Inflight Frames =", MAX_INFLIGHT);
+const BATT_POLL_INTERVAL_MS = Math.max(1_000, SETTINGS.bluetooth.batteryPollIntervalMs);
 
 export type FrameSender = (buffer: ArrayBuffer) => Promise<void>;
 let currentSender: FrameSender | null = null;
+let battPollTimer: ReturnType<typeof setInterval> | null = null;
+let isBattPollInFlight = false;
+
+function stopBattPolling() {
+    if (battPollTimer) {
+        clearInterval(battPollTimer);
+        battPollTimer = null;
+    }
+}
+
+function shouldSkipBattPoll(): boolean {
+    return isListing || isFileTransferring || uploadState.active;
+}
+
+async function pollBatteryInfo() {
+    if (!currentSender || isBattPollInFlight || shouldSkipBattPoll()) {
+        return;
+    }
+
+    isBattPollInFlight = true;
+    try {
+        await requestBattInfo();
+    } catch (error) {
+        console.debug("Periodic BATT_INFO request failed:", error);
+    } finally {
+        isBattPollInFlight = false;
+    }
+}
+
+function startBattPolling() {
+    stopBattPolling();
+    battPollTimer = setInterval(() => {
+        void pollBatteryInfo();
+    }, BATT_POLL_INTERVAL_MS);
+}
 
 export function registerTransport(sender: FrameSender | null) {
     currentSender = sender;
@@ -21,6 +57,7 @@ export function registerTransport(sender: FrameSender | null) {
 // NEU: Wird von bluetooth.ts oder serial.ts nach dem physischen Connect gerufen
 export async function handleTransportConnect(sender: FrameSender) {
     registerTransport(sender);
+    stopBattPolling();
 
     try {
         // Basis-Informationen zwingend vorab laden
@@ -28,9 +65,11 @@ export async function handleTransportConnect(sender: FrameSender) {
         await requestFSInfo();
         await requestDeviceInfo();
         await requestFWInfo();
+        await requestBattInfo();
 
         // Erst wenn diese Basisdaten da sind, wird die UI freigeschaltet
         isConnected.set(true);
+        startBattPolling();
     } catch (error) {
         console.error("Transport-Initialisierung fehlgeschlagen:", error);
         handleTransportDisconnect();
@@ -58,6 +97,10 @@ export async function requestFWInfo() {
     await sendFrame(buildFWInfoRequest());
 }
 
+export async function requestBattInfo() {
+    await sendFrame(buildBattInfoRequest());
+}
+
 let isListing = false;
 
 export async function fetchDirectory(path: string): Promise<any[]> {
@@ -66,6 +109,8 @@ export async function fetchDirectory(path: string): Promise<any[]> {
     }
     isListing = true;
 
+    console.debug(`[Transport] fetchDirectory(${path})`);
+
     return new Promise(async (resolve, reject) => {
         // Dem Parser sagen, wen er bei Erfolg/Fehler anrufen soll
         setLsResolver(
@@ -83,6 +128,7 @@ export async function fetchDirectory(path: string): Promise<any[]> {
 }
 
 export function handleTransportDisconnect() {
+    stopBattPolling();
     registerTransport(null);
     resetRemote();
 }
@@ -95,6 +141,8 @@ export async function getFile(path: string): Promise<boolean> {
     }
     isFileTransferring = true;
 
+    console.debug(`[Transport] getFile(${path})`);
+
     return new Promise(async (resolve, reject) => {
         setFileGetResolver(
             (result: any) => { isFileTransferring = false; resolve(result.success); },
@@ -116,6 +164,8 @@ export async function getTags(path: string): Promise<Blob> {
     }
     isFileTransferring = true;
 
+    console.debug(`[Transport] getTags(${path})`);
+
     return new Promise(async (resolve, reject) => {
         setFileGetResolver(
             (result: any) => {